SPEED LIMITER SYSTEM Speed Limiter System does not Operate

DESCRIPTION

When the warning canceling switch is turned on, the ECM will illuminate the speed limiter indicator light and activate the speed limiter system. Each function of the speed limiter system can be activated by operating the cruise control switch. While the cruise control system is operating, the speed limiter system will not activate.

WIRING DIAGRAM

A00DRT4E14

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK CRUISE CONTROL SYSTEM


    1. Turn the ignition switch to ON.

    2. Turn the cruise control switch on.

    3. Check the operation of each function by operating the cruise control switch Click here.

      OK
      Each function of the cruise control system operates normally.

    NG

    GO TO CRUISE CONTROL SYSTEM Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (WARNING CANCELING SWITCH)


    1. Use the Data List to check if the warning canceling switch is functioning properly.

      Cruise Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ASL Main Switch Warning canceling switch signal / ON or OFF

      ON: Warning canceling switch on

      OFF: Warning canceling switch off

      		 -
      OK
      On screen, item changes between ON and OFF according to above chart.

    NG

    INSPECT WARNING CANCELING SWITCH ASSEMBLY Click here

    OK

  3. CHECK DTC OUTPUT (CRUISE CONTROL SYSTEM)


    1. Check for DTCs Click here.

      OK
      DTC P0500 or P0503 is not output.
      Result
      Result Proceed to
      OK (for 1ZR-FAE) A
      OK (for 2ZR-FAE) B
      OK (for 3ZR-FAE) C
      NG D

    B

    REPLACE ECM Click here

    C

    REPLACE ECM Click here

    D

    GO TO CRUISE CONTROL SYSTEM Click here

    A

    REPLACE ECM Click here

  4. INSPECT WARNING CANCELING SWITCH ASSEMBLY

    A00DR87E01
    Text in Illustration
    *1

    Component without harness connected

    (Warning Canceling Switch)

    1. for LHD:

      Remove the warning canceling switch Click here.

    2. for RHD:

      Remove the warning canceling switch Click here.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      9 (ASL) - 6 (E) Warning canceling switch on Below 1 Ω
      Warning canceling switch off 10 kΩ or higher
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    B

    REPLACE WARNING CANCELING SWITCH ASSEMBLY Click here

    C

    REPLACE WARNING CANCELING SWITCH ASSEMBLY Click here

    A

  5. CHECK HARNESS AND CONNECTOR (WARNING CANCELING SWITCH - ECM AND BODY GROUND)


    1. A00DQQ8E01
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Warning Canceling Switch)
      *2

      Front view of wire harness connector

      (to ECM)

      Disconnect the D70 switch connector.

    2. Disconnect the A40 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D70-9 (ASL) - A40-14 (ASLM) Always Below 1 Ω
      D70-6 (E) - Body ground
      D70-9 (ASL) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      OK (for 1ZR-FAE) A
      OK (for 2ZR-FAE) B
      OK (for 3ZR-FAE) C
      NG D

    B

    REPLACE ECM Click here

    C

    REPLACE ECM Click here

    D

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    A

    REPLACE ECM Click here