STARTER INSTALLATION


  1. INSTALL FLYWHEEL HOUSING SIDE COVER


    1. Install the flywheel housing side cover to the cylinder block.

  2. INSTALL STARTER ASSEMBLY


    1. Install the starter with the 2 bolts.

      Torque:
      37 N*m  { 380 kgf*cm, 27 ft.*lbf }

    2. Connect the connector.

    3. Connect the starter wire with the nut.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

    4. Connect the terminal cap.

  3. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET (for CVT)

    A00DTIV

    1. Install the No. 1 transmission control cable bracket to the continuously variable transaxle with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  4. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT)


    1. Connect the transmission control cable to the bracket with a new clip.

  5. INSTALL BATTERY CARRIER


    1. A010H4O

      Install the battery carrier with the 4 bolts.

      Torque:
      19 N*m  { 189 kgf*cm, 14 ft.*lbf }
    2. A010IJW

      Install the radiator pipe with the 2 bolts.

      Torque:
      19 N*m  { 189 kgf*cm, 14 ft.*lbf }

    3. Connect the 2 wire harness clamps.

  6. INSTALL BATTERY TRAY

  7. INSTALL BATTERY

  8. INSTALL BATTERY CLAMP SUB-ASSEMBLY


    1. A010JUCE01

      Install the battery clamp with the bolt and nut.

      Torque:
      for bolt
      17 N*m  { 168 kgf*cm, 12 ft.*lbf }
      for nut
      3.5 N*m  { 36 kgf*cm, 31 in.*lbf }

    2. Connect the cable to the positive (+) battery terminal.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  9. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    1. A00OKSA

      Connect the air cleaner cap with the band.

    2. Connect the ventilation hose.

    3. A00OMGP

      Connect the 2 clamps.

    4. A00OKGM

      Attach the wire harness to the 2 clamps.

    5. Connect the mass air flow meter connector.

  10. INSTALL NO. 1 ENGINE UNDER COVER


    1. A010GKL

      Install the under cover with the 10 clips.

  11. INSTALL NO. 1 ENGINE UNDER COVER (for Rough Road Area Specification Vehicles)


    1. A010KZT

      Install the under cover with the 3 clips.

  12. INSTALL FRONT LOWER BUMPER ABSORBER


    1. A010FYT

      Install the front lower bumper absorber with the 3 screws and 8 bolts.

    2. A010J5V

      Install the 4 screws and 2 bolts.

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  14. INSTALL RADIATOR SUPPORT OPENING COVER


    1. A00OKW2

      Install the radiator support opening cover with the 7 clips.

  15. REMOVE NO. 2 CYLINDER HEAD COVER


    1. A00OIJQ

      Attach the 4 clips to install the cover.

      Note


      • Be sure to attach the clips securely.

      • Do not apply excessive force or hit the cover to attach the clips. This may cause the cover to break.