EXHAUST MANIFOLD INSTALLATION


  1. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

    A010GPF

    1. Install the heat insulator with the 3 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  2. INSTALL EXHAUST MANIFOLD


    1. Install a new exhaust manifold gasket.

    2. for Nut Type A:


      1. A010I2TE01
        Text in Illustration
        *A Nut Type A
        *B Nut Type B

        Install the exhaust manifold with the 5 nuts.

        Torque:
        21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    3. for Nut Type B:


      1. Install the exhaust manifold with 5 new nuts.

        Torque:
        26 N*m  { 265 kgf*cm, 19 ft.*lbf }

  3. INSTALL MANIFOLD STAY

    A010HS6E01

    1. Temporarily install the manifold stay with the 3 bolts.

    2. While pushing the manifold stay toward the exhaust manifold, tighten the 2 bolts labeled 1.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

    3. Tighten the bolt labeled 2.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  4. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. A010I0OE01

      Using a vernier caliper, measure the free length of the compression springs.

      Minimum Free Length
      Item Specified Condition
      Front side 41.5 mm (1.63 in.)
      Rear side 38.5 mm (1.52 in.)

      If the free length is less than the minimum, replace the compression spring.

    2. A010LUXE11
      Text in Illustration
      *1 Gasket
      *2 Wooden Block

      Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold.

      Note


      • Be sure to install the gasket so that it faces the correct direction.

      • Do not reuse the gasket.

      • Do not damage the gasket.

      • When connecting the exhaust pipe, do not push in the gasket with the exhaust pipe.

    3. A010HB9

      Install the 2 exhaust pipe supports, and then install the front exhaust pipe assembly with the 2 compression springs and 2 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }
    4. A010LUXE11
      Text in Illustration
      *1 Gasket
      *2 Wooden Block

      Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front exhaust pipe assembly.

      Note


      • Be sure to install the gasket so that it faces the correct direction.

      • Do not reuse the gasket.

      • Do not damage the gasket.

      • When connecting the exhaust pipe, do not push in the gasket with the exhaust pipe.

    5. A010GUG

      Connect the front exhaust pipe assembly to the tailpipe assembly with the 2 compression springs and 2 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

    6. Connect the heated oxygen sensor connector.

    7. Attach the clamp to connect the heated oxygen sensor wire harness.

  5. INSTALL FRONT CENTER FLOOR BRACE

    A010KKV

    1. Install the floor brace with the 4 bolts.

      Torque:
      51 N*m  { 520 kgf*cm, 38 ft.*lbf }

  6. INSTALL NO. 2 ENGINE UNDER COVER


    1. A010HXI

      Install the under cover with the 4 clips.

  7. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    1. A010IVS

      Install the heat insulator with the 3 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  8. INSTALL WIRE HARNESS CLAMP BRACKET


    1. A010I9Z

      Install the bracket with the bolt.

      Torque:
      60 N*m  { 612 kgf*cm, 44 ft.*lbf }

  9. INSTALL AIR FUEL RATIO SENSOR


    1. A00DS6PE01

      Using SST, install the sensor to the exhaust manifold.

      SST
      09224-00010
      Torque:
      without SST
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }
      with SST
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Tech Tips

      Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

      Note

      Do not damage the sensor.

    2. A00DQXA

      Connect the sensor connector and clamp.

  10. INSTALL OUTER COWL TOP PANEL

    A010HPX

    1. Install the outer cowl top panel with the 9 bolts.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

  11. INSTALL WINDSHIELD WIPER MOTOR AND LINK


    1. Install the windshield wiper motor and link Click here.

  12. INSTALL NO. 2 CYLINDER HEAD COVER


    1. A00OMDB

      Attach the 4 clips to install the cover.

      Note


      • Be sure to attach the clips securely.

      • Do not apply excessive force or hit the cover to attach the clips. This may cause the cover to break.

  13. INSPECT FOR EXHAUST GAS LEAK

    If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.