FUEL INJECTOR INSTALLATION


  1. INSTALL FUEL INJECTOR ASSEMBLY


    1. A005SKRE06
      Text in Illustration
      *1 O-Ring
      *2 Injector Vibration Insulator

      Install a new injector vibration insulator to the fuel injector.

    2. Apply a light coat of gasoline or spindle oil to the contact surfaces of the O-ring of the fuel injector.

    3. A005V3S

      While turning the fuel injector left and right, install it to the fuel delivery pipe.

      Note


      • Do not twist the O-ring.

      • After installing the fuel injectors, check that they turn smoothly. If not, replace the O-ring with a new one.

  2. INSTALL NO. 1 DELIVERY PIPE SPACER


    1. A005TP6

      Install the 2 No. 1 delivery pipe spacers to the cylinder head.

      Note

      Install the No. 1 delivery pipe spacers in the correct direction.

  3. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY


    1. A005RGA

      Install the fuel delivery pipe with the 4 fuel injector assemblies, and then temporarily install the 2 bolts.

      Note


      • Do not drop the fuel injectors when installing the fuel delivery pipe.

      • Check that the fuel injector assemblies rotate smoothly after installing the fuel delivery pipe.

    2. A005RGA

      Tighten the 2 bolts to the specified torque.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    3. A005T15

      Install the bolt to secure the fuel delivery pipe.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    4. A005TUW

      Install the wire harness bracket with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  4. CONNECT FUEL TUBE SUB-ASSEMBLY


    1. A005SQLE04
      Text in Illustration
      *1 Retainer
      *2 Pipe
      *3 O-Ring

      Push the fuel tube sub-assembly connector onto the fuel delivery pipe until a "click" sound can be heard.

      Note


      • Check that there are no scratches or foreign matter around the contact surfaces of the fuel tube connector and pipe before performing this step.

      • After connecting the fuel tube, check that the fuel tube connector and pipe are securely connected by pulling on them.

    2. A005TP5E07
      Text in Illustration
      *1 Claw

      Install a new No. 2 fuel pipe clamp.

  5. INSTALL AIR TUBE


    1. A005SSG

      Install the air tube with the 2 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    2. Connect the No. 1 vacuum transmitting hose and No. 1 fuel vapor feed hose.

    3. Connect the union to connector tube hose.

    4. Connect the fuel vapor feed hose to the purge VSV.

  6. CONNECT ENGINE WIRE


    1. A005RXN

      Install the 2 wire harness brackets with the 2 bolts.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }
    2. A005SHZ

      Connect the 4 wire harness clamps.

    3. A005S3E

      Connect the 4 fuel injector assembly connectors.

    4. Connect the 2 wire harness clamps.

    5. Connect the ground wires with the 2 bolts.

      Torque:
      8.4 N*m  { 86 kgf*cm, 74 in.*lbf }

  7. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    1. A00DQ1D

      Install the air cleaner case with the 3 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Attach the wire harness clamp to the air cleaner case.

  8. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    1. A005W5Q

      Connect the air cleaner cap with the band.

    2. Connect the ventilation hose.

    3. A005U5E

      Connect the 2 clamps.

    4. A005UEV

      Attach the wire harness to the 2 clamps.

    5. Connect the mass air flow meter connector.

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  10. INSPECT FOR FUEL LEAK


    1. Make sure that there are no fuel leaks after performing maintenance on the fuel system.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the ignition switch to ON, and push the intelligent tester main switch on.

        Note

        Do not start the engine.

      3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

      4. Check that there are no leaks from the fuel system.

      5. Turn the ignition switch off.

      6. Disconnect the intelligent tester from the DLC3.

  11. INSTALL NO. 2 CYLINDER HEAD COVER


    1. A005VFG

      Attach the 4 clips to install the cover.

      Note


      • Be sure to attach the clips securely.

      • Do not apply excessive force or hit the cover to attach the clips. This may cause the cover to break.

  12. INSTALL RADIATOR SUPPORT OPENING COVER


    1. A00DRS1

      Install the radiator support opening cover with the 8 clips.

  13. INSTALL ENGINE ROOM SIDE COVER


    1. A00DRIG

      Install the engine room side cover with the clip.