FUEL INJECTOR REMOVAL


  1. DISCHARGE FUEL SYSTEM PRESSURE


    1. Discharge fuel system pressure Click here.

  2. REMOVE RADIATOR SUPPORT OPENING COVER


    1. A00OKW2

      Remove the 7 clips and radiator support opening cover.

  3. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE NO. 2 CYLINDER HEAD COVER


    1. A010LI3

      Hold the rear of the cover and raise it to detach the 2 clips on the rear of the cover. Continue to raise the cover to detach the 2 clips on the front of the cover and remove the cover.

      Note

      Attempting to detach both front and rear clips at the same time may cause the cover to break.

  6. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. A010LIZ

      Disconnect the mass air flow meter connector.

    2. Detach the wire harness from the 2 clamps.

    3. A010LJ4

      Disconnect the 2 clamps.

    4. A010IQW

      Disconnect the ventilation hose.

    5. Loosen the band and remove the air cleaner cap.

  7. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    1. A010IG6

      Detach the wire harness clamp from the air cleaner case.

    2. Remove the 3 bolts and air cleaner case.

  8. REMOVE BATTERY CLAMP SUB-ASSEMBLY


    1. A00OLE3E01

      Disconnect the cable from the positive (+) battery terminal.

    2. Remove the bolt and loosen the nut.

    3. Remove the battery clamp.

  9. REMOVE BATTERY

  10. REMOVE BATTERY TRAY

  11. DISCONNECT ENGINE WIRE


    1. Detach the 10 clamps, and then disconnect the connectors.

    2. Remove the 3 bolts and 2 nuts, and then disconnect the engine wire.

      A010JMB

  12. REMOVE AIR TUBE


    1. Disconnect the fuel vapor feed hose from the purge VSV.

    2. A010LFM

      Disconnect the 2 union to connector tube hoses.

    3. Disconnect the No. 2 air hose and No. 1 fuel vapor feed hose.

    4. Remove the 2 bolts and air tube.

  13. REMOVE WIRE HARNESS CLAMP BRACKET


    1. A010LNL

      Remove the 2 nuts and wire harness clamp bracket.

  14. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    1. A010JFQE01
      Text in Illustration
      *1 Claw

      Remove the No. 2 fuel pipe clamp.

    2. A010J09E01

      Wipe off any dirt on the fuel tube connector.

    3. Hold the fuel tube connector and install SST.

      SST
      09268-21010

    4. Turn SST to align the retainer inside the fuel tube connector with the chamfered part of SST.

    5. Insert SST into the fuel tube and hold it. Then push the fuel tube connector toward SST.

    6. Mount the retainer of the fuel tube connector onto the chamfered part of SST.

    7. A010I0XE17
      Text in Illustration
      *1 O-Ring
      *2 Retainer
      *3 Pipe
      *4 Nylon Tube
      *5 Fuel Tube Connector

      Slide SST and the fuel tube connector together towards the fuel tube until they make a "click" sound, and then disconnect the fuel tube.

    8. Drain the fuel remaining inside the fuel tube.

    9. Cover the fuel tube and fuel pipe with a plastic bag to protect the disconnected parts.

  15. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    1. A010K0Y

      Remove the bolt and wire harness bracket.

    2. A010GMR

      Remove the 2 bolts.

    3. A010LLF

      Remove the bolt and fuel delivery pipe.

    4. A010LJY

      Remove the 2 No. 1 delivery pipe spacers.

  16. REMOVE FUEL INJECTOR ASSEMBLY


    1. A010K9X

      Pull the 4 fuel injector assemblies out of the fuel delivery pipe sub-assembly.

    2. A010INA

      For reinstallation, attach a tag or label to the injector shaft.

      Note

      Prevent entry of foreign objects by covering the fuel injector with plastic bags.

    3. A010K1E

      Remove the 4 injector vibration insulators.