ENTRY AND START SYSTEM (for Start Function), Diagnostic DTC:B2286, P0335

DTC Code DTC Name
B2286 Runnable Signal Malfunction
P0335 Crankshaft Position Sensor Circuit Malfunction (NE Signal)

DESCRIPTION

The power management control ECU and ECM are connected by a cable and the CAN communication lines. These DTCs are stored when the cable information of the crankshaft position sensor signal and CAN information of the crankshaft position sensor signal are inconsistent.

Tech Tips

When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.

DTC Code DTC Detection Condition Trouble Area

B2286

P0335

 The cable information of the crankshaft position sensor signal and CAN information of the crankshaft position sensor signal are inconsistent.

  • AM2 NO. 2 fuse

  • SFI system

  • Power management control ECU

  • Harness or connector

WIRING DIAGRAM

A00DQAZE01

INSPECTION PROCEDURE

Note


  • When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

  • Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips

After replacing the ECM, perform the key ID code registration. Refer to the Service Bulletin for the registration procedure.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)


    1. A00DQRLE01
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to Power Management Control ECU)

      Disconnect the D75 power management control ECU connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      D75-2 (AM21) - Body ground Always 9.5 to 16 V
      D75-1 (AM22) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)


    1. Disconnect the D75 power management control ECU connector.

    2. A00DQRLE02
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to Power Management Control ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D75-6 (GND) - Body ground Always Below 1 Ω
      D75-5 (GND2) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ECM)


    1. Disconnect the D76 power management control ECU connector.

      A00DU4UE01

    2. Disconnect the A40 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      D76-4 (NE) - A40-39 (NEO) Always Below 1 Ω
      D76-4 (NE) - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Rear view of wire harness connector

      (to Power Management Control ECU)

      		 *2

      Front view of wire harness connector

      (to ECM)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. READ VALUE USING INTELLIGENT TESTER (ENGINE CONDITION)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Power Source Control / Data List.

    5. According to the display on the intelligent tester, read the Data List.

      Power Source Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Engine Condition Engine condition/Stop or Run

      Stop: Engine stopped

      Run: Engine running

      		 -
      OK
      Stop (engine stopped) or Run (engine running) appears on the screen according to the engine condition.

      Tech Tips

      *: SFI system:



    NG

    CHECK POWER MANAGEMENT CONTROL ECU Click here

    OK

    GO TO SFI SYSTEM* (HOW TO PROCEED WITH TROUBLESHOOTING)

  5. CHECK POWER MANAGEMENT CONTROL ECU


    1. Reconnect the power management control ECU connectors.

      A00DPYWE08

    2. Using an oscilloscope, check the engine speed input signal waveform at the terminal of the power management control ECU.

      Standard Frequency
      Tester Connection Condition Specified Condition
      D76-4 (NE) - Body ground Engine stopped No pulse generated
      Engine running

      Pulse generated

      (1000 rpm: 200 Hz)
      Text in Illustration
      *1

      Component with harness connected

      (Power Management Control ECU)

      Tech Tips

      *: SFI system



    NG

    GO TO SFI SYSTEM* (HOW TO PROCEED WITH TROUBLESHOOTING)

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here