REAR DOOR LOCK INSTALLATION

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A00OHVZE01

      Install the rear door inside locking cable.

    2. A00OJ0D

      Attach the 3 claws.

  2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A00OJFP

      Install the rear door lock remote control cable.

    2. A00OJDD

      Attach the claw.

  3. INSTALL REAR DOOR LOCK ASSEMBLY LH

    Note


    • When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the surface of the connector which contacts the door lock wiring harness seal.

    • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may allow water intrusion in the connection. This may result in a malfunction of the rear door lock assembly.


    1. Apply MP grease to the sliding parts of the rear door lock assembly.

    2. Install a new door lock wiring harness seal to the rear door lock assembly.

    3. A003D2FE01

      Insert the rear door lock assembly into the rear door outside handle release plate, and set it to the rear door panel.

    4. Check sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

    5. Using a T30 "TORX" wrench, install the rear door lock assembly with the 3 screws.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    6. A003CGK

      Attach the clamp.

  4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A00OHTA

      Install the front side of the glass run.

    2. A00OJ2KE01

      Apply MP grease to the sliding areas of the glass channel as shown in the illustration.

      Standard
      Area Specified Condition
      A 130 mm (5.12 in.)
      B 29 mm (1.14 in.)
    3. A00OLI6

      Slide the rear door glass sub-assembly as shown in the illustration to install it.

  5. INSTALL REAR DOOR QUARTER WINDOW GLASS LH


    1. A00OM0ME01

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  6. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A00OI3W

      Insert the rear door window division bar sub-assembly from above.

    2. Install the rear door window division bar sub-assembly to the glass run.

    3. A00ONZLE01

      Install the rear door window division bar sub-assembly with the 2 bolts and screw.

      Torque:
      6.2 N*m  { 63 kgf*cm, 55 in.*lbf, for bolt and screw }

  7. INSTALL REAR DOOR GLASS RUN LH


    1. A00OJE5E01

      Completely install the glass run.

  8. INSTALL REAR DOOR SERVICE HOLE COVER LH


    1. Apply butyl tape to the door.

    2. A00OLXQE01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable and rear door inside locking cable through a new rear door service hole cover.

      Note


      • When installing the service hole cover, pull the links and connectors through the service hole cover.

      • There should be no wrinkles or folds after attaching the service hole cover.

      • After attaching the service hole cover, check the seal quality.

    3. Attach the rear door service hole cover by using the reference points on the rear door panel.

    4. Connect the connector.

  9. INSTALL REAR INNER DOOR GLASS WEATHERSTRIP LH


    1. A00ONN2

      Install the rear door inner glass weatherstrip to the door panel.

  10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A00OHTZ

      Connect the 2 cables to the inside handle.

    2. for 11 Speakers:

      Connect the connector.

    3. A00OMWWE01
      Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade

      Attach the rear door trim board with the 4 claws on the rear door inner glass weatherstrip.

    4. A00OLBB

      Install the rear door trim board with the 8 clips.

    5. Install the 3 screws.

  11. INSTALL REAR DOOR REGULATOR INSIDE HANDLE PLATE (w/o Power Window)


    1. Install the rear door regulator inside handle plate.

  12. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. Temporarily install the rear door window regulator handle assembly and fully open the window.

    2. Install the snap ring to the rear door window regulator handle assembly.

    3. A00OLNQE02

      Install the rear door window regulator handle assembly as shown in the illustration.

      Standard
      Area Specified Condition
      A 2.4° to 22.4°
      Text in Illustration
      *1 Front Side

  13. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A00OKMD

      Attach the 6 claws and clip to install the rear power window regulator switch assembly with rear door armrest base panel.

  14. INSTALL ASSIST GRIP COVER LH


    1. A00ONY6

      Attach the 10 claws to install the door assist grip cover.

  15. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A00OKFB

      Attach the 3 claws to install the rear door inside handle bezel plug.

  16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.