REAR DOOR LOCK REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A010HOS

      Using moulding remover A, detach the 3 claws and remove the bezel plug.

  4. REMOVE ASSIST GRIP COVER LH


    1. A010HM7

      Using moulding remover A, detach the 10 claws and remove the assist grip cover.

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A010K1N

      Using moulding remover A, detach the 6 claws and the clip.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  6. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. A010LNI

      Insert clip remover between the plate and trim board.

    2. Turn the handle counterclockwise to remove the snap ring and handle.

  7. REMOVE REAR DOOR REGULATOR INSIDE HANDLE PLATE (w/o Power Window)


    1. Remove the inside handle plate.

  8. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A010K0H

      Remove the 3 screws.

    2. Using a clip remover, detach the 8 clips.

    3. A010J2PE01
      Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade

      Pull out the rear door trim board in the direction indicated by the arrow.

    4. for 11 Speakers:


      1. Disconnect the connector.

    5. A010HB4

      Disconnect the 2 cables from the inside handle.

  9. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH


    1. A010HQX

      Remove the inner glass weatherstrip by pulling it upward in the direction indicated by the arrow in the illustration.

  10. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A010I2V

      Disconnect connector and remove the service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  11. REMOVE REAR DOOR GLASS RUN LH


    1. A010JRGE01

      Remove the rear door glass run.

  12. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A010J8PE01

      Remove the screw.

    2. Remove the 2 bolts and rear door window division bar sub-assembly.

  13. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A010LE3E01

      Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.

  14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A010GQV

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  15. REMOVE REAR DOOR LOCK ASSEMBLY LH


    1. A00ONTN

      Detach the clamp.

    2. A00OII5E01

      Using a T30 "TORX" wrench, remove the 3 screws.

    3. Move the rear door lock assembly downward, pull the release plate out of the rear door outside handle frame, and remove the rear door lock assembly and cables as a unit.

    4. Remove the door lock wiring harness seal from the rear door lock assembly.

  16. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A010I32

      Using a screwdriver, detach the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A010G7G

      Remove the rear door remote control cable.

  17. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A010K4K

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A010KBME01

      Remove the rear door inside locking cable.