REAR DOOR LOCK REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note


    • w/ Navigation System (for HDD):

      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A003B33

      Using moulding remover A, detach the 3 claws and remove the bezel plug.

  3. REMOVE ASSIST GRIP COVER LH


    1. A003ECP

      Using moulding remover A, detach the 10 claws and remove the assist grip cover.

  4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A003BSU

      Using moulding remover A, detach the 6 claws and the clip.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  5. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. A003APQ

      Insert clip remover between the plate and trim board.

    2. Turn the handle counterclockwise to remove the snap ring and handle.

  6. REMOVE REAR DOOR REGULATOR INSIDE HANDLE PLATE (w/o Power Window)


    1. Remove the inside handle plate.

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A003BXN

      Remove the 3 screws.

    2. Using a clip remover, detach the 8 clips.

    3. A003D6XE01
      Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade

      Pull out the rear door trim board in the direction indicated by the arrow.

    4. for 11 Speakers:


      1. Disconnect the connector.

    5. A003BQW

      Disconnect the 2 cables from the inside handle.

  8. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH


    1. A003D5U

      Remove the inner glass weatherstrip by pulling it upward in the direction indicated by the arrow in the illustration.

  9. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A003CKZ

      Disconnect connector and remove the service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  10. REMOVE REAR DOOR GLASS RUN LH


    1. A003E0FE01

      Remove the rear door glass run.

  11. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A003D71E01

      Remove the screw.

    2. Remove the 2 bolts and rear door window division bar sub-assembly.

  12. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A003AZJE01

      Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.

  13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A003DIM

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  14. REMOVE REAR DOOR LOCK ASSEMBLY LH


    1. A003CGK

      Detach the clamp.

    2. A003E6HE01

      Using a T30 "TORX" wrench, remove the 3 screws.

    3. Move the rear door lock assembly downward, pull the release plate out of the rear door outside handle frame, and remove the rear door lock assembly and cables as a unit.

    4. Remove the door lock wiring harness seal from the rear door lock assembly.

  15. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A003DGN

      Using a screwdriver, detach the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A003CF2

      Remove the rear door remote control cable.

  16. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A003D66

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A003BFME01

      Remove the rear door inside locking cable.