SFI SYSTEM, Diagnostic DTC:P0102, P0103

DTC Code DTC Name
P0102 Mass or Volume Air Flow Circuit Low Input
P0103 Mass or Volume Air Flow Circuit High Input

DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine the fuel injection time and to provide the appropriate air fuel ratio.

Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the mass air flow meter. The voltage level is proportional to the air flow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

Tech Tips

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.

A005VQQE01
DTC No. DTC Detection Condition Trouble Area
P0102

Mass air flow meter voltage is below 0.2 V for 3 seconds

(1 trip detection logic)


  • Open or short in mass air flow meter circuit


  • Mass air flow meter


  • ECM

P0103

Mass air flow meter voltage is higher than 4.9 V for 3 seconds

(1 trip detection logic)


  • Open or short in mass air flow meter circuit


  • Mass air flow meter


  • ECM

Tech Tips

When any of these DTCs are output, check the air-flow rate by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / MAF.

Mass Air Flow Rate (g/sec.) Malfunction
Approximately 0.0
  • Open in mass air flow meter power source circuit


  • Open or short in VG circuit

271.0 or more
  • Open in E2G circuit

WIRING DIAGRAM

A005W6IE06

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK DTC OUTPUT


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / DTC.

    5. Read the DTC.

      Result
      Result Proceed to
      DTC P0102 is output A
      DTC P0103 is output B

    B
    A
  2. INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)


    1. A005SQPE48
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Mass Air Flow Meter)

      Disconnect the mass air flow meter connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      B2-3 (+B) - Body ground Ignition switch ON 11 to 14 V
    4. Reconnect the mass air flow meter connector.


    NG
    OK
  3. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)


    1. A005RGGE03
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Mass Air Flow Meter)

      *2

      Front view of wire harness connector

      (to ECM)

      Disconnect the mass air flow meter connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for open)
      Tester Connection Condition Specified Condition
      B2-5 (VG) - B39-69 (VG) Always Below 1 Ω
      B2-4 (E2G) - B39-92 (E2G) Always Below 1 Ω
      Standard Resistance (Check for short)
      Tester Connection Condition Specified Condition
      B2-5 (VG) or B39-69 (VG) - Body ground Always 10 kΩ or higher
    4. Reconnect the mass air flow meter connector.

    5. Reconnect the ECM connector.


    NG
    OK
  4. INSPECT MASS AIR FLOW METER


    1. Inspect the mass air flow meter Click here.


    NG
    OK
  5. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY)

    A005T0IE01
    Text in Illustration
    *1

    Front view of wire harness connector

    (to Mass Air Flow Meter)

    *2

    Front view of wire harness connector

    (to Integration Relay)


    1. Disconnect the mass air flow meter connector.

    2. Remove the integration relay (EFI MAIN relay) from the engine room No. 1 relay block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for open)
      Tester Connection Condition Specified Condition
      B2-3 (+B) - 1B-4 Always Below 1 Ω
      Standard Resistance (Check for short)
      Tester Connection Condition Specified Condition
      B2-3 (+B) or 1B-4 - Body ground Always 10 kΩ or higher
    4. Reconnect the mass air flow meter connector.

    5. Reinstall the integration relay.


    NG
    OK
  6. CHECK HARNESS AND CONNECTOR (SENSOR GROUND)


    1. A005SQPE49
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Mass Air Flow Meter)

      Disconnect the mass air flow meter connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B2-4 (E2G) - Body ground Always Below 1 Ω
    3. Reconnect the mass air flow meter connector.


    NG
    OK
  7. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)


    1. A005RGGE04
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Mass Air Flow Meter)

      *2

      Front view of wire harness connector

      (to ECM)

      Disconnect the mass air flow meter connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for open)
      Tester Connection Condition Specified Condition
      B2-4 (E2G) - B39-92 (E2G) Always Below 1 Ω
      Standard Resistance (Check for short)
      Tester Connection Condition Specified Condition
      B2-4 (E2G) or B39-92 (E2G) - Body ground Always 10 kΩ or higher
    4. Reconnect the mass air flow meter connector.

    5. Reconnect the ECM connector.


    NG
    OK