SFI SYSTEM Fuel Injector Circuit

DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

A005SL6E01
A005T3GE01

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)


    1. A005TMRE39
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Fuel Injector Assembly)

      Disconnect the fuel injector assembly connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      B10-1 - Body ground Ignition switch ON 11 to 14 V
      B11-1 - Body ground Ignition switch ON 11 to 14 V
      B12-1 - Body ground Ignition switch ON 11 to 14 V
      B13-1 - Body ground Ignition switch ON 11 to 14 V

    3. Turn the ignition switch off.

    4. Reconnect the fuel injector assembly connectors.


    NG

    CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [IG2 RELAY] - FUEL INJECTOR ASSEMBLY) Click here

    OK

  2. INSPECT FUEL INJECTOR ASSEMBLY


    1. Inspect the fuel injector assembly Click here.


    NG

    REPLACE FUEL INJECTOR ASSEMBLY

    OK

  3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)


    1. A005UU9E57
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Fuel Injector Assembly)
      *2

      Front view of wire harness connector

      (to ECM)

      Disconnect the fuel injector assembly connectors.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      B10-2 - B39-86 (#10) Always Below 1 Ω
      B11-2 - B39-85 (#20) Always Below 1 Ω
      B12-2 - B39-84 (#30) Always Below 1 Ω
      B13-2 - B39-83 (#40) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      B10-2 or B39-86 (#10) - Body ground Always 10 kΩ or higher
      B11-2 or B39-85 (#20) - Body ground Always 10 kΩ or higher
      B12-2 or B39-84 (#30) - Body ground Always 10 kΩ or higher
      B13-2 or B39-83 (#40) - Body ground Always 10 kΩ or higher

    4. Reconnect the fuel injector assembly connectors.

    5. Reconnect the ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

    OK

    REPLACE ECM Click here

  4. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [IG2 RELAY] - FUEL INJECTOR ASSEMBLY)


    1. A005RENE05
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Fuel Injector Assembly)
      *2 Engine Room No. 1 Relay Block
      *3

      Front view of wire harness connector

      (to Integration Relay)

      Disconnect the fuel injector assembly connectors.

    2. Remove the integration relay from the engine room No. 1 relay block.

    3. Disconnect the integration relay connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      B10-1 - 1A-4 Always Below 1 Ω
      B11-1 - 1A-4 Always Below 1 Ω
      B12-1 - 1A-4 Always Below 1 Ω
      B13-1 - 1A-4 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      B10-1 or 1A-4 - Body ground Always 10 kΩ or higher
      B11-1 or 1A-4 - Body ground Always 10 kΩ or higher
      B12-1 or 1A-4 - Body ground Always 10 kΩ or higher
      B13-1 or 1A-4 - Body ground Always 10 kΩ or higher

    5. Reconnect the fuel injector connector.

    6. Reinstall the integration relay.

    7. Reconnect the integration relay connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [IG2 RELAY] - FUEL INJECTOR ASSEMBLY)

    OK

    CHECK ECM POWER SOURCE CIRCUIT Click here