МЕХАНИЧЕСКАЯ ТРАНСМИССИЯ В СБОРЕ УСТАНОВКА


  1. INSTALL MANUAL TRANSMISSION UNIT

    A01J5WXE01

    1. Align the input shaft with the clutch disc and install the transmission unit to the engine.

    2. Install the 7 bolts.

      Torque:
      72 N*m  { 730 kgf*cm, 53 ft.*lbf, for bolt A }
      37 N*m  { 377 kgf*cm, 27 ft.*lbf, for bolt B }

  2. INSTALL EXHAUST MANIFOLD STAY

    A01J4UUE02

    1. Install the exhaust manifold stay with the 3 bolts.

      Torque:
      44 N*m  { 449 kgf*cm, 32 ft.*lbf, for bolt A }
      30 N*m  { 306 kgf*cm, 22 ft.*lbf, for bolt B }
      72 N*m  { 730 kgf*cm, 53 ft.*lbf, for bolt C }

  3. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

    A01J5L8E07

    1. Install the mounting insulator with the 4 bolts.

      Torque:
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }

  4. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

    A01J6ICE20

    1. Install the frame crossmember with the 4 bolts and 4 nuts labeled A.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    2. Install the 4 set bolts labeled B to the No. 1 engine mounting insulator rear.

      Torque:
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }

  5. INSTALL STARTER ASSEMBLY

    Click here

  6. CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

    A01J616E02

    1. Install the clutch release cylinder with the 2 bolts.

      Torque:
      12 N*m  { 120 kgf*cm, 9 ft.*lbf }

  7. CONNECT WIRE HARNESS


    1. Connect the back-up light switch connector and speedometer sensor connector.

  8. INSTALL FRONT EXHAUST PIPE ASSEMBLY

    Click here

  9. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

    Click here

  10. ADD MANUAL TRANSMISSION OIL

    Click here

  11. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY


    1. Cover the shift lever cap with a cloth.

    2. Press down on the shift lever cap and rotate it clockwise to install it.

      Tech Tips

      Apply MP grease to the tip of the shift lever.

  12. INSTALL SHIFT LEVER BOOT ASSEMBLY

    A01J400E01

    1. Install the shift lever boot with the 4 screws and 2 clips.

  13. INSTALL CONSOLE BOX ASSEMBLY

    Click here

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

  15. PERFORM INITIALIZATION


    1. Perform initialization Click here.

      Note

      Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.

  16. INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY

    Torque:
    28 N*m  { 286 kgf*cm, 21 ft.*lbf }

  17. INSTALL NO. 2 ENGINE UNDER COVER

    Torque:
    28 N*m  { 286 kgf*cm, 21 ft.*lbf }

  18. INSTALL NO. 1 ENGINE UNDER COVER

    Torque:
    28 N*m  { 286 kgf*cm, 21 ft.*lbf }