БЛОК МЕХАНИЧЕСКОЙ ТРАНСМИССИИ УСТАНОВКА


  1. INSTALL OUTPUT SHAFT ASSEMBLY

    A01J39H

    1. Apply gear oil to the sliding part of the output shaft.

    2. Using a plastic-faced hammer, install the output shaft by rapping the intermediate plate.

  2. INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING

    A01J4OD

    1. Using a snap ring expander, install the shaft snap ring to the output shaft.

  3. INSTALL INPUT SHAFT ASSEMBLY

    A01J4G7E02

    1. Apply gear oil to the input shaft and No. 2 synchronizer ring, and install them to the output shaft.

      Note


      • Install the No. 2 synchronizer ring so that its groove fits into the No. 2 synchromesh shifting key.

      • Check that the input shaft rotates slightly.

  4. INSTALL COUNTER GEAR

    A01J77UE02

    1. Temporarily install the counter gear to the intermediate plate.

  5. INSTALL COUNTER SHAFT CENTER BEARING

    A01J4LDE01

    1. Using SST and a hammer, tap in a new center bearing to the intermediate plate.

      SST
      09316-60011   ( 09316-00011 )

      Tech Tips

      Install the bearing while tapping the tip of the counter gear with a plastic-faced hammer so that the counter gear will not hit the side wall of the output shaft gear by being pushed forward.

  6. INSTALL REVERSE IDLER GEAR

    A01J7ONE02

    1. Apply gear oil to each sliding part of the reverse idler gear and the reverse idler gear shaft, and install the reverse idler gear and the reverse idler shaft to the intermediate plate.

      Note

      Face the groove side of the reverse idler shaft to the rear side, and install it from the rear side.

  7. INSTALL REAR BEARING RETAINER

    A01J3UDE02

    1. Install the bearing retainer inserting to the groove of the reverse idler gear shaft with the 4 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  8. INSTALL 5TH GEAR THRUST WASHER PIN

    A01J64F

    1. Apply MP grease to the washer pin, and install it to the counter gear.

  9. INSTALL 5TH GEAR THRUST WASHER

    A01J4Y7

    1. Apply gear oil to the thrust washer, and install it to the counter gear.

      Note

      Install the thrust washer so that its chamfer side faces to the front side.

  10. INSTALL NO. 3 SYNCHROMESH SHIFTING KEY


    1. Apply gear oil to the sliding part of the No. 3 transmission hub sleeve, and install it to the counter 5th gear.

      Note

      Be sure of the direction of the No. 3 transmission hub sleeve and the counter 5th gear.

    2. A01J6UAE02

      Install the 2 No. 3 synchromesh shifting keys and No. 3 synchromesh shifting key spring to the counter 5th gear as shown in the illustration.

      Tech Tips

      When installing the No. 3 synchromesh shifting key spring, make sure the protrusion fits into the cutout.

      Install the No. 3 synchromesh shifting key.

    3. A01J4KP

      Using a snap ring expander, install the snap ring to the counter 5th gear.

  11. INSTALL COUNTER 5TH GEAR BEARING

    A01J5H6E01

    1. Apply gear oil to the bearing and install it to the counter 5th gear.

  12. INSTALL COUNTER 5TH GEAR

    A01J48X

    1. Apply gear oil to the 5th gear and No. 3 transmission hub sleeve, and install it to the counter gear.

  13. INSTALL NO. 3 SYNCHRONIZER RING

    A01J7I5

    1. Apply gear oil to the No. 3 synchronizer ring, and install it to the counter gear.

      Note

      Install the No. 3 synchronizer ring so that its groove fits into the No. 3 synchromesh shifting key.

  14. INSTALL NO. 5 GEAR SPLINE PIECE

    A01J3UZE01

    1. Using SST and a press, press in the gear spline piece to the counter gear.

      SST
      09316-60011   ( 09316-00011 )

      Note

      Check that the gear rotate freely.

  15. INSTALL COUNTER GEAR REAR SHAFT SNAP RING


    1. Select the snap ring so that the thrust gap between the No. 5 gear spline piece and snap ring to be within the specification.

      Standard clearance
      0.10 mm (0.0039 in.) or less
      Standard snap ring thickness
      Thickness
      2.80 to 2.85 mm (0.1102 to 0.1122 in.)
      2.85 to 2.90 mm (0.1122 to 0.1141 in.)
      2.90 to 2.95 mm (0.1141 to 0.1160 in.)
      2.95 to 3.00 mm (0.1160 to 0.1181 in.)
      3.00 to 3.05 mm (0.1181 to 0.1200 in.)
      3.05 to 3.10 mm (0.1200 to 0.1220 in.)
      3.10 to 3.15 mm (0.1220 to 0.1240 in.)
    2. A01J7J7

      Using a brass bar and hammer, tap in the snap ring.

  16. INSPECT COUNTER 5TH GEAR THRUST CLEARANCE

    A01J7LFE02

    1. Using a feeler gauge, measure the thrust clearance.

      Standard clearance
      0.10 to 0.35 mm (0.0039 to 0.0138 in.)

      If the clearance is not as specified, replace the counter shaft 5th gear and No. 3 synchronizer ring.

  17. INSPECT COUNTER 5TH GEAR RADIAL CLEARANCE

    A01J43PE02

    1. Using a dial indicator, check the gear radial clearance.

      Standard clearance
      0.015 to 0.068 mm (0.0006 to 0.0027 in.)

      If the clearance is not as specified, replace the counter 5th gear bearing.

  18. INSTALL OUTPUT SHAFT REAR BEARING

    A01J6G7E05

    1. Using SST and a press, press in the spacer and a new rear bearing to the output shaft.

      SST
      09309-35010

  19. INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING


    1. Select a shaft snap ring so that the thrust gap between the output shaft bearing shaft and snap ring to be within the specification.

      Standard clearance
      0.10 mm (0.0039 in.) or less
      Standard snap ring thickness
      Thickness Thickness
      2.65 to 2.70 mm (0.1043 to 0.1063 in.) 3.10 to 3.15 mm (0.1220 to 0.1240 in.)
      2.70 to 2.75 mm (0.1063 to 0.1083 in.) 3.15 to 3.20 mm (0.1240 to 0.1260 in.)
      2.75 to 2.80 mm (0.1083 to 0.1102 in.) 3.20 to 3.25 mm (0.1260 to 0.1280 in.)
      2.80 to 2.85 mm (0.1102 to 0.1122 in.) 3.25 to 3.30 mm (0.1280 to 0.1299 in.)
      2.85 to 2.90 mm (0.1122 to 0.1141 in.) 3.30 to 3.35 mm (0.1299 to 0.1319 in.)
      2.90 to 2.95 mm (0.1141 to 0.1160 in.) 3.35 to 3.40 mm (0.1319 to 0.1339 in.)
      2.95 to 3.00 mm (0.1160 to 0.1181 in.) 3.40 to 3.45 mm (0.1339 to 0.1358 in.)
      3.00 to 3.05 mm (0.1181 to 0.1200 in.) 3.45 to 3.50 mm (0.1358 to 0.1378 in.)
      3.05 to 3.10 mm (0.1200 to 0.1220 in.) -
    2. A01J4I0

      Using a brass bar and hammer, tap in the snap ring.

  20. INSTALL SPEEDOMETER DRIVE GEAR

    A01J440E04

    1. Using snap ring pliers, install the snap ring.

    2. Install the ball and drive gear.

    3. Using snap ring pliers, install the snap ring.

  21. INSTALL REVERSE SHIFT ARM BRACKET


    1. A01J4Y5

      Install the reverse shift arm to the reverse shift arm bracket with a new snap ring.

    2. A01J6OQE04

      Insert the tip of the reverse shift arm into the reverse idler gear.

    3. A01J4SR

      Install the reverse shift arm bracket with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    4. A01J7AV

      Install the torsion spring to the reverse shift arm bracket.

      Note

      Make sure that the torsion spring is securely installed to the reverse shift arm.

  22. INSTALL REVERSE SHIFT FORK


    1. A01J60S

      Install the reverse shift fork to the reverse shift arm.

  23. INSTALL NO. 3 SHIFT FORK SHAFT


    1. A01J33JE03

      Install the No. 1 shift interlock roller to the intermediate plate.

    2. A01J6ZY

      Install the No. 3 shift fork to the No. 3 transmission hub sleeve and No. 3 shift fork shaft to the intermediate plate from the front side.

    3. A01J32C

      Install the straight pin to the reverse shift fork.

    4. A01J75Y

      Using a brass bar and hammer, tap in the snap ring to the shift fork shaft.

    5. A01J42U

      Using a 5 mm pin punch and hammer, tap in the slotted spring pin to the No. 3 shift fork.

  24. INSTALL NO. 1 SHIFT FORK SHAFT


    1. A01J33JE04

      Install the No. 1 shift interlock roller to the intermediate plate.

    2. A01J3IO

      Install the No. 1 shift fork to the reverse gear.

    3. A01J3Q1

      Install the No. 1 shift fork shaft to the intermediate plate from the rear side.

    4. A01J7MY

      Install a new bolt to the No. 1 shift fork.

      Torque:
      20 N*m  { 199 kgf*cm, 14 ft.*lbf }
    5. A01J6Z7

      Using a brass bar and hammer, tap in the shift fork shaft snap ring to the No. 1 shift fork shaft.

  25. INSTALL NO. 2 SHIFT FORK SHAFT

    A01J4QBE02

    1. Install the shift interlock pin and No. 1 shift interlock roller to the intermediate plate.

    2. A01J7L7

      Install the No. 2 shift fork to the No. 2 transmission hub sleeve.

    3. A01J6SB

      Apply gear oil to the No. 2 shift fork, and install to the intermediate plate from the rear side.

    4. A01J325

      Install a new bolt to the No. 2 shift fork.

      Torque:
      20 N*m  { 199 kgf*cm, 14 ft.*lbf }
    5. A01J44L

      Using a brass bar and a hammer, tap in the snap ring to the No. 2 shift fork shaft.

  26. INSTALL NO. 1 SHIFT DETENT BALL SPRING SEAT

    A01J598

    1. Install the 2 compression springs and 2 shifts detent balls to the intermediate plate.

    2. A01J3ZB

      Using a T40 ''TORX'' socket wrench, install the 2 spring seats to the intermediate plate.

      Torque:
      19 N*m  { 189 kgf*cm, 14 ft.*lbf }
    3. A01J6YME02

      Install the detent ball and low side compression spring to the intermediate plate.

    4. A01J6WWE02

      Using a T40 ''TORX'' socket wrench, install the spring seat to the intermediate plate.

      Torque:
      19 N*m  { 189 kgf*cm, 14 ft.*lbf }

  27. INSTALL TRANSMISSION MAGNET

    A01J5QTE02

    1. Clean the transmission magnet, and install it to the intermediate plate.

  28. INSTALL MANUAL TRANSMISSION CASE

    A01J71PE09

    1. Apply seal packing to the manual transmission case as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
    2. A01J5RUE01

      Using a plastic-faced hammer, tap the transmission case to attach it to the intermediate plate.

  29. INSTALL NO. 1 COUNTER GEAR FRONT BEARING SNAP RING

    A01J5NRE02

    1. Using a snap ring expander, install the snap ring to the transmission case.

  30. INSTALL FRONT BEARING SHAFT SNAP RING

    A01J6PME02

    1. Using a snap ring expander, install the snap ring to the transmission case.

  31. INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL

    A01J3B1E05

    1. Using SST and a hammer, tap in a new oil seal to the front bearing retainer.

      SST
      09950-60010   ( 09951-00300, 09951-00520, 09952-06010 )
      09950-70010   ( 09951-07100 )
      Oil seal depth
      11.20 to 12.20 mm (0.4409 to 0.4803 in.)

    2. Lightly apply MP grease to the tip of the oil seal.

  32. INSTALL FRONT BEARING RETAINER

    A01J4Q7E01

    1. Apply seal packing to the bearing retainer as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
    2. A01J6TGE02

      Install the front bearing retainer to the transmission case with the 8 bolts.

      Torque:
      17 N*m  { 168 kgf*cm, 12 ft.*lbf }

    3. Check that the input shaft and output shaft rotate smoothly.

  33. INSTALL EXTENSION HOUSING OIL SEAL

    A01J3BGE01

    1. Using SST and a hammer, tap in a new oil seal to the extension housing.

      SST
      09710-30050
      09950-70010   ( 09951-07100 )
      Oil seal depth
      0 +- 0.5 mm (0 +- 0.020 in.)

      Note

      Be careful not to damage the oil seal lip.

    2. Lightly apply MP grease to the tip of the oil seal.

  34. INSTALL REVERSE RESTRICT PIN

    A01J38UE02

    1. Install the restrict pin to the extension housing.

    2. A01J7EKE02

      Using a 5 mm pin punch and hammer, tap in the slotted pin to the extension housing.

    3. A01J6JGE02

      Using a T40 ''TORX'' socket wrench, install the plug to the transfer adapter.

      Torque:
      19 N*m  { 189 kgf*cm, 14 ft.*lbf }

  35. INSTALL OIL RECEIVER


    1. Install the oil receiver with the bolt.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  36. INSTALL OIL RECEIVER PIPE

    A01J5V5E02

    1. Install the oil receiver pipe to the extension housing.

  37. INSTALL EXTENSION HOUSING


    1. A01J71PE09

      Apply seal packing to the extension housing as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    2. Insert the shift and select lever to the extension housing.

    3. A01J5TIE04

      Connect the shift and select lever to the fork shaft and put in the shift lever housing.

    4. Align the shift and select lever to the extension housing installation hole and push in the extension housing.

    5. A01J4SXE01

      Install the extension housing to the case with the 10 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
    6. A01J4XME02

      Install the shift lever housing bolt to the shift lever housing.

      Torque:
      33 N*m  { 340 kgf*cm, 25 ft.*lbf }

  38. INSTALL CONTROL SHIFT LEVER RETAINER

    A01J2ZM

    1. Install a new control shift lever retainer gasket and the control shift lever retainer with the 6 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  39. INSTALL RESTRICT PIN

    A01J2ZFE03

    1. Install the 2 restrict pins.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  40. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

    A01J54UE02

    1. Using SST, install a new gasket and back-up light switch and to the transmission case.

      SST
      09817-16011
      Torque:
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }

  41. INSTALL SPEEDOMETER DRIVEN GEAR


    1. Install a new O-ring to the speedometer driven gear.

    2. Install the speedometer driven gear with the bolt.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  42. INSTALL CLUTCH HOUSING

    A01J6RI

    1. Install the clutch housing to the transmission case with the 9 bolts.

      Torque:
      36 N*m  { 367 kgf*cm, 27 ft.*lbf }

  43. INSTALL CLUTCH RELEASE FORK BOOT

    A01J63B

    1. Install the fork boot to the clutch housing.

  44. INSTALL RELEASE FORK SUPPORT

    A01J6WGE02

    1. Install the release fork support to the clutch housing.

      Torque:
      47 N*m  { 479 kgf*cm, 35 ft.*lbf }

  45. INSTALL CLUTCH RELEASE BEARING ASSEMBLY

    A01J4SZE01

    1. Apply Multemp 8158 Grease or equivalent to the clutch release bearing, and install it to the clutch release fork with the clip.

      Grease
      Multemp 8158 Grease or equivalent

  46. INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

    A01J4QYE02

    1. Install the clutch release fork.

    2. Apply the clutch spline grease to the spline of the input shaft.

      Grease
      Toyota Genuine Clutch Spline Grease or equivalent

  47. INSTALL DRAIN PLUG

    A01J468E02

    1. Install a new gasket and the drain plug to the transmission case.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  48. INSTALL FILLER PLUG

    A01J5LYE02

    1. Install a new gasket and the filler plug to the transmission case.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }