БЛОК АВТОМАТИЧЕСКОЙ ТРАНСМИССИИ ПРОВЕРКА


  1. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

    A01J4BUE01

    1. Remove the magnets, and use them to collect steel particles.

    2. Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.


      • Steel (magnetic): bearing, gear and clutch plate wear

      • Brass (non-magnetic): bushing wear

  2. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY

    A01J5P5E01

    1. Hold the reverse clutch hub and turn the No. 2 1-Way clutch assembly.

    2. Check that the No. 2 1-Way clutch assembly turns freely clockwise and locks when turned counterclockwise.

  3. INSPECT NO. 3 BRAKE DISC

    A01J5V7E01

    1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

      Note

      Before assembling new discs, soak them in ATF for at least 15 minutes.

  4. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

    A01J6I4E01

    1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

      Standard free length
      15.72 mm (0.619 in.)

  5. INSPECT FRONT PLANETARY GEAR ASSEMBLY

    A01J6BSE01

    1. Using a feeler gauge, measure the front planetary pinion gear thrust clearance.

      Standard clearance
      0.2 to 0.60 mm (0.008 to 0.024 in.)
      Maximum clearance
      0.65 mm (0.026 in.)

      • If the clearance is greater than the maximum, replace the front planetary gear assembly.

    2. A01J450E01

      Using a dial indicator, measure the inside diameter of the front planetary gear bushing.

      Maximum inside diameter
      57.48 mm (2.263 in.)

      • If the inside diameter is greater than the maximum, replace the front planetary gear.

  6. INSPECT 1-WAY CLUTCH ASSEMBLY

    A01J5A1E01

    1. Install the 1-way clutch assembly to the 1-way clutch inner race.

    2. Hold the 1-way clutch inner race and turn the 1-way clutch assembly.

    3. Check that the 1-way clutch assembly turns freely counterclockwise and locks when turned clockwise.

    4. Remove the 1-way clutch assembly from 1-way clutch inner race.

  7. INSPECT NO. 1 BRAKE DISC

    A01J5V7E01

    1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

      Note

      Before assembling new discs, soak them in ATF for at least 15 minutes.

  8. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

    A01J5R0E01

    1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

      Standard free length
      17.05 mm (0.671 in.)

  9. INSPECT NO. 2 BRAKE DISC

    A01J5V7E01

    1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

      Note

      Before assembling new discs, soak them in ATF for at least 15 minutes.

  10. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

    A01J6GBE01

    1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

      Standard free length
      17.45 mm (0.687 in.)

  11. INSPECT CENTER PLANETARY GEAR ASSEMBLY

    A01J506E01

    1. Using a feeler gauge, measure the center planetary gear pinion thrust clearance.

      Standard clearance
      0.12 to 0.68 mm (0.005 to 0.027 in.)
      Maximum clearance
      0.73 mm (0.029 in.)

      • If the clearance is greater than the maximum, replace the center planetary gear assembly.

  12. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY

    A01J4KIE01

    1. Hold the rear planetary ring gear flange sub assembly and turn the 1-way clutch assembly.

    2. Check that the 1-way clutch assembly turns freely counterclockwise and locks when turned clockwise.

  13. INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

    A01J5I6E01

    1. Using a caliper gauge, measure the inside diameter of the rear planetary ring gear bushing.

      Maximum inside diameter
      32.175 mm (1.267 in.)

      • If the inside diameter is greater than the maximum, replace the rear planetary ring gear.

  14. INSPECT INTERMEDIATE SHAFT

    A01J3CTE01

    1. Using a dial indicator, check the intermediate shaft runout.

      Maximum runout
      0.08 mm (0.003 in.)

      Note

      If the bend exceeds the specification, replace the intermediate shaft with a new one.

    2. A01J55YE02

      Using a micrometer, check the outer diameter of the intermediate shaft positions shown in the diagram.

      Standard diameter
      A
      25.962 to 25.975 mm (1.022 to 1.023 in.)
      B
      25.962 to 25.975 mm (1.022 to 1.023 in.)
      C
      32.062 to 32.075 mm (1.262 to 1.263 in.)
      D
      32.062 to 32.075 mm (1.262 to 1.263 in.)
      Minimum diameter
      A
      25.912 mm (1.020 in.)
      B
      25.912 mm (1.020 in.)
      C
      32.012 mm (1.260 in.)
      D
      32.012 mm (1.260 in.)

      Note

      If the outer diameter is outside the standard or less than the minimum, replace the intermediate shaft with the new one.

  15. INSPECT NO. 4 BRAKE DISC

    A01J5V7E01

    1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

      Note

      Before assembling new discs, soak them in ATF for at least 15 minutes.

  16. INSPECT REAR PLANETARY GEAR ASSEMBLY

    A01J5H2E01

    1. Using a feeler gauge, measure the rear planetary gear pinion thrust clearance.

      Standard clearance
      0.2 to 0.6 mm (0.008 to 0.024 in.)
      Maximum clearance
      0.65 mm (0.026 in.)

      • If the clearance is greater than the maximum, replace the planetary gear assembly.

    2. A01J6S7E01

      Using a caliper gauge, measure the inside diameter of the rear planetary gear bushing.

      Maximum inside diameter
      20.075 mm (0.790 in.)

      • If the inside diameter is greater than the maximum, replace the rear planetary gear assembly.

  17. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

    A01J433E01

    1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

      Standard free length
      23.74 mm (0.935 in.)

  18. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE

    A01J5I7E01

    1. Make sure the 1st and reverse brake pistons move smoothly when applying and releasing the compressed air into the transmission case.

  19. INSPECT NO. 1 PISTON STROKE OF BRAKE PISTON

    A01J6NFE01

    1. Make sure the No. 1 brake piston moves smoothly when applying and releasing the compressed air into the transmission case.

  20. INSPECT INDIVIDUAL PISTON OPERATION INSPECTION

    A01J5YWE02

    1. Check the operating sound while applying compressed air into the oil holes indicated in the illustration.

      Tech Tips

      When inspecting the O/D direct clutch, check with the C3 accumulator piston holes indicated in the illustration.

      If there is no sound, disassembly and check the installation condition of the parts.


      • (1) No. 2 clutch (C2)

      • (2) No. 3 clutch (C3)

      • (3) No. 1 clutch (C1)

      • (4) No. 3 brake (B1)

      • (5) No. 1 brake (B1)

      • (6) No. 2 brake (B2)

      • (7) No. 4 brake (B4)