ЖИДКОСТЬ ДЛЯ АВТОМАТИЧЕСКОЙ ТРАНСМИССИИ РЕГУЛИРОВКА


  1. BEFORE REFILL TRANSMISSION

    A01J364E01

    • This transmission requires Toyota Genuine ATF WS transmission fluid.

    • After servicing the transmission, you must refill the transmission with the correct amount of fluid.

    • Maintain the vehicle in a horizontal position while adjusting the fluid level.

    • Proceed to the ''TRANSMISSION PAN FILL'' procedures if you replaced the entire transmission, transmission pan, drain plug, valve body and/or torque converter.

    • Proceed to the ''TRANSMISSION FILL'' procedures after removing the refill plug if you replaced the transmission hose and/or output shaft oil seal.

  2. TRANSMISSION PAN FILL

    A01J73IE01

    1. Remove the refill plug and overflow plug.

    2. Fill the transmission through the refill hole until fluid begins to trickle out of the overflow tube.

    3. Reinstall the overflow plug.

  3. TRANSMISSION FILL


    1. Fill the transmission with the amount of fluid listed in the table below.

    2. Reinstall the refill plug to prevent the fluid from splashing.

      Standard capacity
      Repair Fill Amount
      Transmission pan and drain plug removal 1.7 liters (1.8 US qts, 1.5 Imp. qts)
      Transmission valve body removal 4.3 liters (4.54 US qts, 3.78 Imp. qts)
      Torque converter removal 5.4 liters (5.71 US qts, 4.75 Imp. qts)

      Tech Tips

      If you cannot add the listed amount of fluid, do the following:


      1. Install the refill plug.

      2. Allow the engine to idle with the air conditioning OFF.

      3. Move the shift lever through the entire gear range to circulate fluid.

      4. Wait for 30 seconds with the engine idling.

      5. Stop the engine.

      6. Remove the refill plug and add fluid.

      7. Reinstall the refill plug.

  4. FLUID CIRCULATION


    1. Allow the engine to idle with the air conditioning OFF.

    2. Move the shift lever through the entire gear range to circulate fluid.

  5. FLUID TEMPERATURE CHECK


    1. A01J5U2E03

      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.

      SST
      09843-18040

    2. Depress and hold the brake pedal.

    3. Start the engine.

      Note

      Check that electrical systems, such as the air conditioning system, audio system and lighting system, are off.

      Tech Tips

      The indicator lights in the meter blink to indicate output DTCs when terminals TC and CG are connected.

    4. Slowly move the shift lever from P to D, and then back to P.

      Tech Tips

      Slowly move the shift lever to circulate the fluid through each part of the transmission.

    5. Move the shift lever back and forth between N and D at 1.5 second intervals for 6 seconds.

    6. A01J4NG

      The A/T OIL TEMP indicator turns on for 2 seconds when the combination meter starts to detect the fluid temperature.

    7. The A/T OIL TEMP indicator turns on again when the fluid temperature reaches 36°C (97°F) and blinks when it exceeds 46°C (115°F).

  6. FLUID LEVEL CHECK

    A01J73IE01

    Note

    The fluid temperature must be between 36°C (97°F) and 46°C (115°F) to check the fluid level.


    1. Remove the overflow plug with the engine idling.

    2. Check that the fluid comes out of the overflow tube.

      If fluid does not come out, proceed to the ''TRANSMISSION REFILL'' procedures.

      If fluid comes out, wait until the overflow slows to a trickle and proceed to the ''COMPLETE'' procedures.

  7. TRANSMISSION REFILL


    1. Install the overflow plug.

    2. Stop the engine.

    3. Remove the refill plug.

    4. Add 0.4 liters (0.42 US qts, 0.35 Imp. qts) of fluid.

    5. Allow the engine to idle and wait for 10 seconds.

    6. Proceed to the ''FLUID CHECK'' procedures.

  8. COMPLETE


    1. Install the overflow plug with a new gasket.

    2. Stop the engine.

    3. Install the refill plug with a new gasket.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf, for overflow plug }
      39 N*m  { 398 kgf*cm, 29 ft.*lbf, for refill plug }