BLACK OUT TAPE (for Rear Door) REMOVAL

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the LH side.


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work Click here.

  2. REMOVE REAR NO. 3 FLOOR BOARD


    1. Remove the rear No. 3 floor board.

  3. REMOVE DECK FLOOR BOX RH


    1. Fold back the rear No. 2 floor board.

    2. Remove the deck floor box RH Click here.

  4. REMOVE REAR NO. 3 FLOOR BOARD UPPER PLATE


    1. A0040W5

      Disengage the 2 claws and remove the rear No. 3 floor board upper plate.

  5. REMOVE CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A00401M

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug.

  7. REMOVE DOOR ASSIST GRIP COVER


    1. A003ZX2

      Using a moulding remover, disengage the 6 claws, 2 clips and 3 guides, and remove the door assist grip cover.

  8. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A0041MN

      Disengage the 7 claws and 2 guides.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  9. REMOVE REAR DOOR ARMREST COVER


    1. A0041EU

      Remove the rear door armrest cover.

  10. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A0043YGE02
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the rear door panel.

    2. A00429Z

      Remove the 2 screws.

    3. Using a clip remover, disengage the 8 clips.

    4. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.

    5. Raise the rear door trim board sub-assembly and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    6. A00437P

      Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.

    7. for 8 Speakers:


      1. Disconnect the connector.

  11. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A00416C

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly, and remove the rear door inside handle sub-assembly.

  12. REMOVE REAR DOOR FRAME GARNISH


    1. A0042K3

      Disengage the clip and remove the rear door frame garnish.

      Tech Tips

      This garnish needs to be replaced with a new one because the clip will break when removing the rear door frame garnish.

  13. REMOVE REAR DOOR TRIM BRACKET


    1. A0040UH

      Remove the 2 screws and rear door trim bracket.

  14. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A0043E5

      Disconnect the 2 connectors.

    2. Disengage the clamp.

    3. Pass the rear door lock remote control cable, rear door inside locking cable and each connector through the rear door service hole cover.

    4. Remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  15. REMOVE REAR DOOR GLASS RUN


    1. A0043F9

      Remove the rear door glass run.

  16. REMOVE REAR DOOR WINDOW GUIDE SUB-ASSEMBLY


    1. A0043SQ

      Remove the screw.

    2. Remove the bolt and rear door window guide sub-assembly.

  17. REMOVE REAR DOOR REAR GUIDE SEAL


    1. A004411E01
      Text in Illustration
      *1 Temporary Screw

      Loosen the temporary screw.

    2. Remove the 2 screws and rear door rear guide seal.

    3. Remove the temporary screw from the rear door rear guide seal.

  18. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) auxiliary battery terminal and rear power window regulator switch assembly.

    2. Connect the rear power window regulator motor connector.

    3. Move the rear door glass sub-assembly so that the door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) auxiliary battery terminal.

    5. Disconnect the rear power window regulator switch assembly and rear power window regulator motor connector.

    6. A00416K

      Remove the 2 bolts and rear door glass sub-assembly as shown in the illustration.

      Note


      • After the bolts are removed, do not allow the door glass to fall.

      • Do not damage the door glass.

  19. REMOVE REAR DOOR BELT MOULDING ASSEMBLY


    1. A0043RDE01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the rear door belt moulding assembly.

    2. A00440G

      Using a screwdriver, disengage the 7 claws and remove the rear door belt moulding assembly.

  20. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

    Tech Tips

    When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

    Heating Temperature
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the vehicle body or rear door front window frame moulding moulding excessively.


    1. Using a heat light, heat the rear door front window frame moulding.

    2. A00410UE01
      Text in Illustration
      *1 Double-sided Tape

      Using a moulding remover, remove the clip and rear door front window frame moulding.

  21. DISCONNECT REAR DOOR WEATHERSTRIP


    1. A00433Y

      Using a clip remover, disengage the clip and remove the upper part of the rear door weatherstrip to the extent that allows removal of the rear door stripe and black out tape.

  22. REMOVE NO. 2 BLACK OUT TAPE


    1. Using a heat light, heat the No. 2 black out tape and vehicle body.

      Heating Temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)

      Note

      Do not heat the vehicle body excessively.

    2. A0040CM

      Pull back on one of the ends of the No. 2 black out tape to remove it.

      Tech Tips

      When pulling on the tape, pull it parallel to the body.

  23. REMOVE REAR DOOR OUTSIDE STRIPE


    1. Using a heat light, heat the rear door outside stripe and vehicle body.

      Heating Temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)

      Note

      Do not heat the vehicle body excessively.

    2. A00405B

      Pull back on one of the ends of the rear door outside stripe to remove it.

      Tech Tips

      When pulling on the stripe, pull it parallel to the body.

  24. REMOVE REAR DOOR UPPER OUTSIDE STRIPE


    1. Using a heat light, heat the rear door upper outside stripe and vehicle body.

      Heating Temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)

      Note

      Do not heat the vehicle body excessively.

    2. A0042OL

      Pull back on one of the ends of the rear door upper outside stripe to remove it.

      Tech Tips

      When pulling on the stripe, pull it parallel to the body.

  25. REMOVE REAR DOOR LOWER OUTSIDE STRIPE


    1. Using a heat light, heat the rear door lower outside stripe and vehicle body.

      Heating Temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)

      Note

      Do not heat the vehicle body excessively.

    2. A003ZXH

      Pull back on one of the ends of the rear door lower outside stripe to remove it.

      Tech Tips

      When pulling on the stripe, pull it parallel to the body.