OUTER REAR VIEW MIRROR INSTALLATION

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the LH side.


  1. INSTALL OUTER MIRROR COVER


    1. A00408J

      Engage the 7 claws to install the outer mirror cover as shown in the illustration.

      Note


      • Securely engage the claws.

      • Make sure that the outer edge of the outer mirror cover securely fits in the outer rear view mirror assembly.

  2. INSTALL OUTER MIRROR


    1. Connect the 2 connectors.

    2. Engage the 2 guides on the upper part of the outer mirror to the outer mirror.

    3. A00421U

      Engage the 2 claws on the lower part of the outer mirror to the outer mirror.

      Note

      Do not push in the outer mirror with excessive force. Doing so may break the mirror surface.

    4. A004125

      Push the outside part of the outer mirror assembly and tilt it as shown in the illustration.

  3. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY


    1. A0043QB

      Engage the clip to install the outer rear view mirror assembly.

    2. Install the outer rear view mirror assembly with the 3 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    3. Connect the connector.

  4. INSTALL OUTER MIRROR INSTALL HOLE COVER


    1. A00439V

      Engage the guide and 2 claws to install the outer mirror install hole cover.

  5. INSTALL OUTER MIRROR PROTECTOR


    1. A00432O

      Engage the 2 claws.

    2. Install the outer mirror protector with the screw.

  6. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A0041P6

      Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.

    2. A0042J4

      Engage the 2 claws and install the front door inside handle sub-assembly to the front door trim board sub-assembly.

      Note

      Make sure the 2 claws are fully engaged to ensure that the front door lock assembly will operate properly.

  7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A004096

      Engage the 9 clips and install the front door trim board sub-assembly.

    2. Install the 2 screws.

    3. Remove the 2 pieces of protective tape.

  8. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A0041OAE02
      Text in Illustration
      *A for LH Side
      *B for RH Side

      Engage the claw to install the courtesy light assembly.

  9. INSTALL DOOR ARMREST COVER


    1. A0041MF

      Install the door armrest cover.

  10. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A0043X4

      Connect the connector.

    2. Engage the 7 claws and 3 guides, and install the power window regulator master switch assembly with front door armrest base panel.

  11. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. Connect each connector.

    2. A0042YA

      Engage the 7 claws and 3 guides, and install the power window regulator switch assembly with front door armrest base panel.

  12. INSTALL ASSIST GRIP COVER


    1. A0041NT

      Engage the 6 claws, 2 clips and 3 guides, and install the assist grip cover.

  13. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A0040IN

      Engage the 3 claws and install the front door inside handle bezel plug.

  14. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INSTALL REAR NO. 3 FLOOR BOARD UPPER PLATE


    1. Engage the 2 claws to install the rear No. 3 floor board upper plate.

  16. INSTALL DECK FLOOR BOX RH


    1. Install the deck floor box RH Click here.

    2. Install the rear No. 2 floor board.

  17. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.