FRONT WIPER MOTOR INSTALLATION


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY


    1. Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

  3. INSTALL FRONT WIPER CRANK SUB-ASSEMBLY


    1. A0041CX

      Temporarily install a front wiper crank sub-assembly on the windshield wiper motor assembly with the nut.

    2. Temporarily install the windshield wiper motor and link assembly on the crank arm pivot of the front wiper crank sub-assembly.

    3. Align the front wiper crank sub-assembly with the windshield wiper link rod as shown in the illustration.

      A00419ZE02
      Text in Illustration
      *1 Front Wiper Crank Sub-assembly *2 Windshield Wiper Link Rod

    4. Install the front wiper crank sub-assembly with the nut.

      Torque:
      17 N*m  { 175 kgf*cm, 13 ft.*lbf }
    5. A0042IHE01
      Text in Illustration
      *1 Crank Arm Pivot

      Apply MP grease to the crank arm pivot of the front wiper crank sub-assembly.

    6. A0042ZZ

      Connect the rod of the windshield wiper motor and link assembly to the crank arm pivot of the front wiper crank sub-assembly.

  4. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. Connect the connector while the windshield wiper motor and link assembly is placed face down.

      CAUTION:

      To reduce the risk of injury, carefully handle the parts during service.

    2. Engage the 2 clamps.

      CAUTION:

      To reduce the risk of injury, carefully handle the parts during service.

    3. Engage the grommet as shown in the illustration.

      A0041L5E01
      Text in Illustration
      *A for LHD *B for RHD
      *1 Grommet - -

      CAUTION:

      To reduce the risk of injury, carefully handle the parts during service.

    4. Install the windshield wiper motor and link assembly with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    5. Engage the clamp.

  5. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


    1. Engage the 8 guides <B>.

      A00403ME01

    2. Engage the 5 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.

    3. Install the 2 clips.

  6. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


    1. Engage the 8 guides <B>.

      A0041WOE01

    2. Engage the 6 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.

    3. Install the 2 clips.

  7. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    1. A0040ZLE01

      Engage the guide <B> as shown in the illustration.

    2. Engage the claw and guide <A> to install the cowl side ventilator sub-assembly LH as shown in the illustration.

  8. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. Disconnecting the cable from the negative (-) auxiliary battery terminal.

    2. Operate the front wiper arm and blade assembly RH and stop the windshield wiper motor assembly at the automatic stop position.

    3. Connecting the cable to the negative (-) auxiliary battery terminal.

    4. A0041PWE06
      Text in Illustration
      *1 Front Wiper Arm and Blade Assembly RH Serration
      *2 Wire Brush
      *3 Windshield Wiper Link Assembly Pivot Serration

      When reusing the front wiper arm and blade assembly RH:


      1. Clean the front wiper arm and blade assembly RH serration.

    5. When reusing the windshield wiper link assembly:


      1. Clean the windshield wiper link assembly pivot serration with a wire brush.

    6. A003ZY4E01
      Text in Illustration
      *1 Ceramic Dot

      Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }

      Tech Tips

      Hold the front wiper arm and blade assembly RH by hand while tightening the nut.

  10. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. A0041PWE05
      Text in Illustration
      *1 Front Wiper Arm and Blade Assembly LH Serration
      *2 Wire Brush
      *3 Windshield Wiper Link Assembly Pivot Serration

      When reusing the front wiper arm and blade assembly LH:


      1. Clean the front wiper arm and blade assembly LH serration.

    2. When reusing the windshield wiper link assembly:


      1. Clean the windshield wiper link assembly pivot serration with a wire brush.

    3. A0040EBE01
      Text in Illustration
      *1 Ceramic Dot

      Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }

      Tech Tips

      Hold the front wiper arm and blade assembly LH by hand while tightening the nut.

    4. Operate the front wiper arm and blade assemblies while spraying washer fluid on the windshield glass. Make sure that the front wiper arm and blade assemblies function properly and there is no interference with the vehicle body.

  11. INSTALL FRONT WIPER ARM HEAD CAP


    1. A0040D4

      Engage the 3 claws to install the front wiper arm head cap.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  12. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  13. INSTALL REAR NO. 3 FLOOR BOARD UPPER PLATE


    1. Engage the 2 claws to install the rear No. 3 floor board upper plate.

  14. INSTALL DECK FLOOR BOX RH


    1. Engage the claw and 4 guide to install the deck floor box RH.

  15. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.