BACK DOOR GLASS REMOVAL


  1. REMOVE UPPER BACK DOOR TRIM PANEL ASSEMBLY


    1. A0043TV

      Using a moulding remover, disengage the 4 clips and 4 claws, and remove the upper back door trim panel assembly.

  2. REMOVE BACK DOOR SIDE GARNISH RH


    1. A0043NX

      Disengage the 3 clips and 2 claws, and remove the back door side garnish RH.

  3. REMOVE BACK DOOR SIDE GARNISH LH


    1. A0043SN

      Disengage the 3 clips and 2 claws, and remove the back door side garnish LH.

  4. REMOVE BACK DOOR TRIM BOARD ASSEMBLY


    1. A0040AI

      Using a moulding remover, disengage the clip and claw.

    2. A00409C

      Using a moulding remover, disengage the clip and claw.

    3. A0040K2E01

      Disengage the 3 clips in the order shown in the illustration.

    4. A0043OY

      Disengage the 2 clips by pulling the back door trim board assembly in the direction indicated by the arrows in the illustration.

    5. A0043CXE01
      Text in Illustration
      *1 Back Door Trim Board Assembly
      *2 Back Door Panel
      *a The portion that may be damaged due to interference

      Remove the back door trim board assembly by pulling it in the direction indicated by the arrow in the illustration to disengage the 4 clips.

      Note

      Make sure to pull the back door trim board assembly in the direction indicated by the arrow in the illustration. If the back door trim board assembly is removed from the lower part, the door pull handle mounting area may interfere with the back door panel, resulting in damage to the back door trim board assembly.

  5. REMOVE BACK DOOR TRIM BOARD


    1. A0042Y4

      Disengage the 5 clips and 2 guides, and remove the back door trim board.

  6. REMOVE REAR SPOILER ASSEMBLY


    1. A00404P

      Disconnect the connector.

    2. Remove the 5 nuts.

    3. A0041EV

      Disengage the 2 clips to remove the rear spoiler assembly.

  7. REMOVE REAR WIPER ARM HEAD CAP (w/ Resin Wiper Arm)


    1. for Back Door Glass:


      1. Remove the rear wiper arm head cap Click here.

  8. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY


    1. for Back Door Glass:


      1. Remove the rear wiper arm and blade assembly Click here.

  9. REMOVE REAR WIPER MOTOR GROMMET


    1. for Back Door Glass:


      1. Remove the rear wiper motor grommet Click here.

  10. REMOVE REAR WIPER MOTOR ASSEMBLY


    1. for Back Door Glass:


      1. Remove the rear wiper motor assembly Click here.

  11. REMOVE BACK DOOR GLASS


    1. w/o Glass Breakage Sensor:


      1. A004495

        Disconnect the 2 connectors.

    2. w/ Glass Breakage Sensor:


      1. A0043CD

        Disconnect the 4 connectors.

    3. A0041DVE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the outer surface of the vehicle body to prevent scratches.

      Note

      When separating the back door glass from the vehicle, be careful not to damage the paint or interior and exterior ornaments.

    4. A00436BE01
      Text in Illustration
      *1 Piano Wire

      Pass a piano wire between the vehicle body and back door glass from the interior, as shown in the illustration.

      Tech Tips

      Do not allow the piano wire to interfere with the clips.

    5. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

    6. Cut off the adhesive by pulling the piano wire around the back door glass.

      Note

      Leave as much adhesive on the vehicle body as possible when removing the back door glass.

    7. A0041IS

      Using suction cups, disengage the 2 clips and remove the back door glass.

  12. REMOVE NO. 1 BACK DOOR GLASS ADHESIVE DAM


    1. A00423P

      Remove the No. 1 back door glass adhesive dam.

  13. REMOVE NO. 1 BACK WINDOW OUTSIDE MOULDING LH


    1. A00416XE01
      Text in Illustration
      *1 LH Side
      *2 RH Side

      Remove the No. 1 back window outside moulding LH.

  14. REMOVE NO. 1 BACK WINDOW OUTSIDE MOULDING RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  15. REMOVE NO. 1 BACK WINDOW LOWER MOULDING


    1. A0040HY

      Remove the No. 1 back window lower moulding.

  16. REMOVE NO. 2 BACK WINDOW GLASS SPACER


    1. A0043B1E01
      Text in Illustration
      *1 No. 2 Back Window Glass Spacer
      *2 No. 1 Back Window Glass Spacer

      Using a scraper, remove the No. 2 back window glass spacer.

      Note


      • Be careful not to damage the back door glass.

      • Be sure to replace the No. 1 back window glass spacer with a new one.

  17. REMOVE NO. 1 BACK WINDOW GLASS SPACER

    Tech Tips

    Use the same procedure for the No. 1 spacer and No. 2 spacer.

  18. CLEAN BACK DOOR GLASS


    1. A0042ZUE02

      Clean the outer edge of the back door glass with a non-residue solvent.

      Note


      • Do not touch the back door glass surface after cleaning it.

      • Be careful not to damage the glass.

      • Even if using a new back door glass, clean the back door glass with a non-residue solvent.

  19. REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY


    1. for Back Door Window Fix Glass:


      1. Remove the back door outside garnish sub-assembly Click here.

  20. REMOVE BACK WINDOW FIX GLASS


    1. w/o Glass Breakage Sensor:


      1. A0041IO

        Disconnect the 2 connectors.

    2. w/ Glass Breakage Sensor:


      1. A0042PT

        Disconnect the 3 connectors.

    3. A0041GEE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the outer surface of the vehicle body to prevent scratches.

      Note

      When separating the back door glass vehicle, be careful not to damage the interior and exterior ornaments.

    4. A004163E01
      Text in Illustration
      *1 Piano Wire

      Pass a piano wire between the vehicle body and back window fix glass from the interior, as shown in the illustration.

    5. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

    6. Cut off the adhesive by pulling the piano wire around the back door glass.

      Note

      Leave as much adhesive on the vehicle body as possible when removing the back door glass.

    7. A0042EG

      Using suction cups, disengage the 2 clips and remove the back door glass.

  21. REMOVE NO. 2 BACK DOOR GLASS ADHESIVE DAM


    1. A0042TI

      Using a scraper, remove the back door glass adhesive dam.

      Note


      • Be careful not to damage the back window fix glass.

      • Be sure to replace the back door glass adhesive dam with a new one.

  22. REMOVE NO. 2 BACK WINDOW OUTSIDE MOULDING LH


    1. A00400AE01
      Text in Illustration
      *1 LH Side
      *2 RH Side

      Using a scraper, remove the NO. 2 back window outside moulding LH.

      Note


      • Be careful not to damage the back window fix glass.

      • Be sure to replace the back window outside moulding with a new one.

  23. REMOVE NO. 2 BACK WINDOW OUTSIDE MOULDING RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  24. REMOVE NO. 2 BACK WINDOW LOWER MOULDING


    1. A003ZZ4

      Using a scraper, remove the back window lower moulding.

      Note


      • Be careful not to damage the back window fix glass.

      • Be sure to replace the back window lower moulding with a new one.

  25. REMOVE NO. 2 BACK DOOR GLASS SPACER


    1. A004036E01
      Text in Illustration
      *1 No. 2 Back Window Glass Spacer
      *2 No. 1 Back Window Glass Spacer

      Using a scraper, remove the No. 2 back door glass spacer.

      Note


      • Be careful not to damage the back window fix glass.

      • Be sure to replace the No. 2 back window glass spacer with a new one.

  26. REMOVE NO. 1 BACK DOOR GLASS SPACER

    Tech Tips

    Use the same procedure for the No. 1 spacer and No. 2 spacer.

  27. CLEAN BACK WINDOW FIX GLASS


    1. A0042ZUE02

      Clean the outer edge of the back window fix glass with a non-residue solvent.

      Note


      • Do not touch the back window fix glass surface after cleaning it.

      • Be careful not to damage the glass.

      • Even if using a new back window fix glass, clean the back window fix glass with a non-residue solvent.

  28. CLEAN VEHICLE BODY


    1. A0040R4E07
      Text in Illustration
      *1 Adhesive
      *2 Vehicle Body

      Using a scraper, remove the moulding and adhesive from the back window fix glass.

    2. Clean and shape the contact surfaces of the vehicle body.


      1. Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.

        Note

        Be careful not to damage the vehicle body.

        Tech Tips

        Leave as much adhesive on the vehicle body as possible.

      2. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

        Tech Tips

        Even if all the adhesive has been removed, clean the vehicle body.