POWER WINDOW REGULATOR MOTOR (for Rear Door) INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

    Note

    The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.


    1. Using a T25 "TORX" driver, install the rear power window regulator motor assembly with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Tech Tips

      A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

  3. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY


    1. Apply MP grease to the sliding parts of the rear door window regulator assembly.

    2. Install the temporary bolt to the rear door window regulator assembly.

    3. A0042PRE01
      Text in Illustration
      *1 Temporary Bolt

      Temporarily install rear door window regulator assembly.

    4. Tighten the temporary bolt and 5 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) auxiliary battery terminal and the rear power window regulator motor connector.

    2. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

    3. Disconnect the cable from the negative (-) auxiliary battery terminal.

    4. Disconnect the power window regulator switch assembly and rear power window regulator motor connector.

    5. A0040ID

      Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as shown in the illustration.

    6. Install the rear door glass sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  5. INSTALL REAR DOOR REAR GUIDE SEAL


    1. Install the temporary screw to the rear door rear guide seal.

    2. A004411E01
      Text in Illustration
      *1 Temporary Screw

      Temporarily install the rear door rear guide seal.

    3. Install the 2 screws.

    4. Tighten the temporary screw to install the rear door rear guide seal.

  6. INSTALL REAR DOOR WINDOW GUIDE SUB-ASSEMBLY


    1. A0043SQ

      Install the screw.

    2. Install the rear door window guide sub-assembly with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  7. INSTALL REAR DOOR GLASS RUN


    1. A0043F9

      Install the rear door glass run.

  8. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the rear door panel.

    2. A0042JQE01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the 2 connectors.

    5. Engage the clamp.

  9. INSTALL REAR DOOR TRIM BRACKET


    1. A0040UH

      Install the rear door trim bracket with the 2 screws.

  10. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A0043KG

      Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle sub-assembly.

    2. A00437P

      Engage the 2 claws and install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.

      Note

      Make sure the 2 claws are fully engaged to ensure that the rear door lock assembly will operate properly.

  11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. for 8 Speakers:


      1. Connect the connector.

    2. A0043VB

      Engage the 8 clips and install the rear door trim board sub-assembly.

    3. Install the 2 screws.

    4. Remove the protective tape.

  12. INSTALL REAR DOOR ARMREST COVER


    1. A0041EU

      Install the rear door armrest cover.

  13. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A0041MN

      Engage the 7 claws and 2 guides, and install the rear power window regulator switch assembly with rear door armrest base panel.

  14. INSTALL DOOR ASSIST GRIP COVER


    1. A0040E5

      Engage the 6 claws, 2 clips and 3 guides, and install the door assist grip cover.

  15. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A0041DE

      Engage the 3 claws and install the rear door inside handle bezel plug.

  16. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  17. INSTALL REAR NO. 3 FLOOR BOARD UPPER PLATE


    1. Engage the 2 claws to install the rear No. 3 floor board upper plate.

  18. INSTALL DECK FLOOR BOX RH


    1. Install the deck floor box RH Click here.

    2. Install the rear No. 2 floor board.

  19. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  20. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  21. INSPECT POWER WINDOW OPERATION

    Click here