POWER WINDOW REGULATOR MOTOR (for Front Door) INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

    Note

    The regulator arm must be below the intermediate position when installing the front power window regulator motor assembly.


    1. Using a T25 "TORX" driver, install the front power window regulator motor assembly with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Tech Tips

      A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

  3. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY


    1. Apply MP grease to the sliding parts of the front door window regulator assembly.

    2. Install the temporary bolt to the front door window regulator assembly.

    3. A0043CVE02
      Text in Illustration
      *1 Temporary Bolt

      Temporarily install the front door window regulator assembly.

    4. Tighten the temporary bolt and 5 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    5. Connect the connector.

  4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) auxiliary battery terminal.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    3. Disconnect the cable from the negative (-) auxiliary battery terminal and power window regulator master switch assembly.

    4. A0041INE01

      Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.

    5. A00428E

      Install the front door glass sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    6. A004472

      Install the grommet.

  5. INSTALL FRONT DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the front door panel.

    2. A0043PLE02
      Text in Illustration
      *1 Reference Point

      Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.

    3. Attach the front door service hole cover according to the reference points on the front door panel.

      Note

      Securely install the front door service hole cover preventing wrinkles and air bubbles.

  6. INSTALL FRONT DOOR TRIM BRACKET


    1. A0041OZ

      Install the front door trim bracket with the 2 screws.

  7. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A0041P6

      Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.

    2. A0042J4

      Engage the 2 claws and install the front door inside handle sub-assembly to the front door trim board sub-assembly.

      Note

      Make sure the 2 claws are fully engaged to ensure that the front door lock assembly will operate properly.

  8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A004096

      Engage the 9 clips and install the front door trim board sub-assembly.

    2. Install the 2 screws.

    3. Remove the 2 pieces of protective tape.

  9. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A0041OAE02
      Text in Illustration
      *A for LH Side
      *B for RH Side

      Engage the claw to install the courtesy light assembly.

  10. INSTALL DOOR ARMREST COVER


    1. A0041MF

      Install the door armrest cover.

  11. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A0043X4

      Connect the connector.

    2. Engage the 7 claws and 3 guides, and install the power window regulator master switch assembly with front door armrest base panel.

  12. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. Connect each connector.

    2. A0042YA

      Engage the 7 claws and 3 guides, and install the power window regulator switch assembly with front door armrest base panel.

  13. INSTALL ASSIST GRIP COVER


    1. A0041NT

      Engage the 6 claws, 2 clips and 3 guides, and install the assist grip cover.

  14. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A0040IN

      Engage the 3 claws and install the front door inside handle bezel plug.

  15. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. INSTALL REAR NO. 3 FLOOR BOARD UPPER PLATE


    1. Engage the 2 claws to install the rear No. 3 floor board upper plate.

  17. INSTALL DECK FLOOR BOX RH


    1. Install the deck floor box RH Click here.

    2. Install the rear No. 2 floor board.

  18. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  19. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  20. INSPECT POWER WINDOW OPERATION

    Click here