BACK DOOR DISASSEMBLY


  1. REMOVE UPPER BACK DOOR TRIM PANEL ASSEMBLY


    1. A0043TV

      Using a moulding remover, disengage the 4 clips and 4 claws, and remove the upper back door trim panel assembly.

  2. REMOVE BACK DOOR SIDE GARNISH RH


    1. A0043NX

      Disengage the 3 clips and 2 claws, and remove the back door side garnish RH.

  3. REMOVE BACK DOOR SIDE GARNISH LH


    1. A0043SN

      Disengage the 3 clips and 2 claws, and remove the back door side garnish LH.

  4. REMOVE BACK DOOR TRIM BOARD ASSEMBLY


    1. A0040AI

      Using a moulding remover, disengage the clip and claw.

    2. A00409C

      Using a moulding remover, disengage the clip and claw.

    3. A0040K2E01

      Disengage the 3 clips in the order shown in the illustration.

    4. A0043OY

      Disengage the 2 clips by pulling the back door trim board assembly in the direction indicated by the arrows in the illustration.

    5. A0043CXE01
      Text in Illustration
      *1 Back Door Trim Board Assembly
      *2 Back Door Panel
      *a The portion that may be damaged due to interference

      Remove the back door trim board assembly by pulling it in the direction indicated by the arrow in the illustration to disengage the 4 clips.

      Note

      Make sure to pull the back door trim board assembly in the direction indicated by the arrow in the illustration. If the back door trim board assembly is removed from the lower part, the door pull handle mounting area may interfere with the back door panel, resulting in damage to the back door trim board assembly.

  5. REMOVE BACK DOOR TRIM BOARD


    1. A0042Y4

      Disengage the 5 clips and 2 guides, and remove the back door trim board.

  6. REMOVE BACK DOOR LOCK STRIKER COVER


    1. A0041MZ

      Disengage the 2 claws and remove the back door lock striker cover.

  7. REMOVE LOWER BACK DOOR STOPPER CUSHION


    1. A004127

      Disengage the 2 claws to remove the 2 lower back door stopper cushions.

  8. REMOVE BACK DOOR LOCK STRIKER ASSEMBLY


    1. A00410I

      Using a T40 "TORX" socket wrench, remove the 2 screws and back door lock striker assembly.

  9. REMOVE LOWER BACK DOOR STOPPER LH


    1. A004434

      Remove the bolt and lower back door stopper LH.

  10. REMOVE LOWER BACK DOOR STOPPER RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  11. REMOVE BACK DOOR STAY ASSEMBLY LH

    Note


    • Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing.

    • Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.

    • Do not apply any horizontal load to the door stay in order to prevent the piston rod from deforming.


    1. A0043I2E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the 2 stop rings along the groove.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Release the 2 ball joints and remove the back door stay assembly.

      Note

      Remove the back door stay assembly while supporting the back door by hand.

  12. REMOVE BACK DOOR STAY ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  13. REMOVE BACK DOOR STAY BOLT LH


    1. A0043B2

      Remove the back door stay bolt.

  14. REMOVE BACK DOOR STAY BOLT RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  15. REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY


    1. A0043J3E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the back door outside garnish sub-assembly.

    2. A0040FU

      Remove the 4 nuts.

    3. A0043NN

      Disengage the 11 clips and remove the back door outside garnish sub-assembly.

    4. Remove the 11 clips (back door outside garnish clip) from the back door outside garnish sub-assembly.

    5. Remove the 4 gaskets from the back door outside garnish sub-assembly.

  16. REMOVE LICENSE PLATE LIGHT ASSEMBLY LH


    1. A0041P5

      Disconnect the connector.

    2. Disengage the 2 claws and remove the license plate light assembly.

  17. REMOVE LICENSE PLATE LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  18. REMOVE REAR SPOILER ASSEMBLY


    1. A00404P

      Disconnect the connector.

    2. Remove the 5 nuts.

    3. A0041EV

      Disengage the 2 clips to remove the rear spoiler assembly.

  19. REMOVE REAR WASHER NOZZLE


    1. A0043G4

      Disengage the 2 claws.

    2. A00407F

      Disconnect the washer hose and remove the rear washer nozzle.

  20. REMOVE REAR WIPER ARM HEAD CAP (w/ Resin Wiper Arm)


    1. A00447M

      Disengage the 2 claws and open the rear wiper arm head cap as shown in the illustration.

    2. A0042UU

      Disengage the 2 claws and remove the rear wiper arm head cap.

  21. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY


    1. w/ Resin Wiper Arm:


      1. A0040EM

        Remove the nut and rear wiper arm and blade assembly.

    2. w/ Steel Wiper Arm:


      1. A0043WQE01
        Text in Illustration
        *1 Rear Wiper Arm Head Cap

        Open the rear wiper arm head cap.

      2. Remove the nut and rear wiper arm and blade assembly.

  22. REMOVE REAR WIPER MOTOR GROMMET


    1. A004348

      Remove the rear wiper motor grommet.

  23. REMOVE REAR WIPER MOTOR ASSEMBLY


    1. A004140

      Disconnect the connector.

    2. Remove the 3 bolts and rear wiper motor assembly.

  24. REMOVE REAR TELEVISION CAMERA ASSEMBLY (w/ Intelligent Parking Assist System)


    1. A0041RU

      Disconnect the connector.

    2. A0043W0

      Remove the 2 screws.

    3. A0042JM

      Disengage the 4 claws and remove the rear television camera assembly.