ROOF HEADLINING REMOVAL


  1. REMOVE REAR NO. 2 FLOOR BOARD


    1. A00449U

      Using a clip remover, remove the 2 clips.

    2. Disengage the 3 fasteners and remove the rear No. 2 floor board.

  2. REMOVE REAR NO. 3 FLOOR BOARD


    1. Remove the rear No. 3 floor board.

  3. REMOVE DECK FLOOR BOX RH


    1. A00440B

      Disengage the claw and 4 guides and remove the deck floor box RH.

  4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A0042VN

      Disengage the 10 claws and remove the front door scuff plate LH.

  6. REMOVE COWL SIDE TRIM BOARD LH


    1. A0042AR

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim board LH.

  7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A0040RU

      Remove the front door opening trim weatherstrip LH.

  8. REMOVE FRONT PILLAR GARNISH LH


    1. A0043VA

      When removing the front pillar garnish LH, cover the shaded part in the illustration with a piece of cloth so that the interior parts will not be damaged.

    2. A0042S8E01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    3. A0043VFE01

      Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.

      Note


      • Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tech Tips

      Tape the needle-nosed pliers tip before use.

      Text in Illustration
      *1 Protective Tape

    4. Disengage the 3 guides.

    5. A0043ISE01

      Disengage the claw while pressing the shaded part in the illustration in the direction indicated by the arrow (1).

    6. Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.

    7. A0042VXE01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  9. REMOVE REAR DOOR SCUFF PLATE LH


    1. A0040QT

      Disengage the 7 claws and remove the rear door scuff plate LH.

  10. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A0042YY

      Remove the rear door opening trim weatherstrip LH.

  11. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)


    1. A0041VP

      Disengage the 3 claws and remove the lap belt outer anchor cover.

  12. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A0040I7

      Remove the bolt and disconnect the floor end of the front seat outer belt assembly.

  13. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. A0043XN

      Disengage the 2 claws and 2 clips, and remove the center pillar lower garnish LH.

  14. REMOVE CENTER PILLAR GARNISH LH


    1. A00400G

      Remove the screw.

    2. Using a clip remover, disengage the clip.

    3. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH and remove the center pillar garnish LH.

  15. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  20. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  21. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side.

  22. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  23. REMOVE CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  25. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. A0041DUE01
      Text in Illustration
      *1 Front Hook
      *2 Rear Hook

      Disengage the front hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.

      Standard Measurement
      Dimension Measurement
      a 100 mm (3.94 in.) or less

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. Choose a front hook to disengage first. Place your hands near the front hook as shown in the illustration. Then lift the seat cushion to disengage the front hook.

      2. Repeat the above procedure for the other hook.

    2. Disengage the 2 rear hooks of the rear seat cushion assembly from the rear seatback assembly.

    3. Remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  26. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. A0042ZC

      Remove the bolt.

    2. A0043ARE01
      Text in Illustration
      *1 Fastener

      Disengage the fastener.

    3. A0042MX

      Disengage the 2 guides and remove the rear side seatback assembly LH as shown in the illustration.

  27. REMOVE REAR SIDE SEATBACK ASSEMBLY RH


    1. A0041NL

      Remove the bolt.

    2. A0041DQE01
      Text in Illustration
      *1 Fastener

      Disengage the fastener.

    3. A0041ZJ

      Disengage the 2 guides and remove the rear side seatback assembly RH as shown in the illustration.

  28. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

    Click here

  29. REMOVE TONNEAU COVER ASSEMBLY


    1. Remove the tonneau cover assembly.

  30. REMOVE REAR NO. 4 FLOOR BOARD SUB-ASSEMBLY


    1. Remove the rear No.4 floor board sub-assembly.

  31. REMOVE DECK FLOOR BOX LH

    Tech Tips

    Use the same procedure described for the RH side.

  32. REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    1. A0043P1

      Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.

  33. REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    1. A004109

      Disengage the claw and 3 clips, and remove the rear No. 1 floor board sub-assembly.

  34. REMOVE REAR NO. 1 FLOOR BOARD


    1. Fold the rear seatback assembly LH forward.

    2. A0042PSE01
      Text in Illustration
      *1 Fastener

      Disengage the fastener.

    3. Fold the rear seatback assembly LH forward.

    4. A0040XLE01
      Text in Illustration
      *1 Fastener

      Disengage the fastener.

    5. A0043PV

      Using a clip remover, remove the clip.

    6. Disengage the 3 fasteners and remove the rear No. 1 floor board.

  35. REMOVE DECK TRIM SERVICE HOLE COVER


    1. A0040WX

      Disengage the 4 claws.

    2. Disengage the 4 guides and remove the deck trim service hole cover.

  36. REMOVE REAR DECK TRIM COVER


    1. A0043JF

      Disengage the 4 claws and remove the rear deck trim cover.

  37. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    1. A0042TO

      Remove the 2 bolts.

    2. Disengage each guide and remove the 2 luggage hold belt striker assemblies.

  38. REMOVE TONNEAU COVER HOLDER CAP (for LH Side)


    1. A0043ZDE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the claw and remove the tonneau cover holder cap.

      Tech Tips

      Tape the screwdriver tip before use.

  39. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the screw.

      A0041IQ

    2. Disengage the 7 claws and 2 clips.

    3. Disconnect the connector and remove the deck trim side panel assembly LH.

  40. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. Disengage the 9 clips and remove the roof side inner garnish assembly LH.

      A0040V9

  41. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side.

  42. REMOVE TONNEAU COVER HOLDER CAP (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side.

  43. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Remove the screw.

      A0040C2

    2. Disengage the 7 claws and 2 clips, and remove the deck trim side panel assembly RH.

  44. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  45. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A0042AB

      Disconnect the rain sensor cover as shown in the illustration.

    2. Disengage the 2 claws and remove the rain sensor cover.

  46. REMOVE INNER REAR VIEW MIRROR COVER (w/ EC Mirror)


    1. A0041OQ

      Disengage the 2 guides and slide the inner rear view mirror cover as shown in the illustration.

    2. A0042U9

      Disengage the 6 claws and remove the inner rear view mirror cover.

  47. REMOVE ROOF TOP MOULDING


    1. A0043G0

      Using a moulding remover, disengage the 3 claws and 2 clips, and remove the roof top moulding.

  48. REMOVE MAP LIGHT ASSEMBLY


    1. A00446QE01

      Disengage the 4 clips and 2 guides in the order shown in the illustration.

    2. Disconnect the connector and remove the map light assembly.

  49. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    1. A0040EHE01
      Text in Illustration
      *1 Protective Tape
      *a Front

      Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and remove the No. 1 room light lens.

    2. A00410DE01
      Text in Illustration
      *1 Protective Tape
      *a Front

      Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws as shown in the illustration and remove the No. 1 room light housing.

    3. A004196E02
      Text in Illustration
      *1 Room Light Switch Base

      Using a screwdriver, disengage the 4 claws and disconnect the room light switch base from the No. 1 room light housing.

  50. REMOVE FRONT ASSIST GRIP ASSEMBLY


    1. A0043TQE02
      Text in Illustration
      *1 Protective Tape
      *a Allow the covers to come off slightly

      Using a clip remover, disengage the 4 claws.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip covers as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

    2. Pull off the 2 assist grip covers by hand.

    3. A0040YB

      Disengage the 2 clips and remove the front assist grip assembly.

    4. Remove the 2 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the other front assist grip.

  51. REMOVE REAR ASSIST GRIP ASSEMBLY


    1. A0043RME02
      Text in Illustration
      *1 Protective Tape
      *a Allow the covers to come off slightly

      Using a clip remover, disengage the 4 claws.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip covers as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

    2. Pull off the 2 assist grip covers by hand.

    3. A004307

      Disengage the 2 clips and remove the rear assist grip assembly.

    4. Remove the 2 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the other rear assist grip.

  52. REMOVE VISOR BRACKET COVER LH


    1. A0043D7

      Using a moulding remover, disengage the 3 claws and remove the visor bracket cover LH.

  53. REMOVE VISOR ASSEMBLY LH


    1. A0040J8

      Disengage the 2 clips and remove the visor assembly LH.

  54. REMOVE VISOR BRACKET COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  55. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  56. REMOVE VISOR HOLDER


    1. A0042DYE01

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

      Tech Tips

      Use the same procedure for the other visor holder.

  57. REMOVE ROOF HEADLINING ASSEMBLY

    A004463E01
    Text in Illustration
    *A w/o Satellite Radio *B w/ Satellite Radio
    *C for RHD with Rain Sensor *D w/ EC Mirror
    *E for LHD with Rain Sensor - -

    1. w/ Rain Sensor:


      1. Disconnect the rain sensor connector.

    2. w/ EC Mirror:


      1. Disconnect the inner rear view mirror connector.

    3. w/ Rain Sensor or w/ EC Mirror:


      1. Disengage the 2 clamps.

    4. w/o Satellite Radio:


      1. Disengage the 3 clamps and disconnect the connector from the front pillar RH.

    5. w/ Satellite Radio:


      1. Disengage the 3 clamps and disconnect the 2 connectors from the front pillar RH.

    6. Disengage the clamp and disconnect the 2 connectors from the rear pillar RH.

    7. Disengage the 4 clamps from the front pillar LH.

    8. Disconnect the 2 No. 1 roof wire connectors from the connector holder.

    9. Remove the 5 clips.

    10. A0043ND

      Remove the roof headlining assembly from the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.