FRONT SEAT OUTER BELT ASSEMBLY INSTALLATION


  1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. A00446JE01

      Engage the guide to temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.

    2. Fully tighten the bolt <A> first, then the bolt <B> to install the front shoulder belt anchor adjuster assembly.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY


    1. A00401TE01

      Temporarily install the front seat outer belt assembly with the 2 bolts.

    2. Fully tighten the bolt <A> first, then the bolt <B> to install the front seat outer belt assembly.

      Torque:
      Bolt <A>
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }
      Bolt <B>
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A0043Z4

      Connect the pretensioner connector and lock the locking button as shown in the illustration.

      Note

      Securely lock the locking button.

    4. A0040B0

      Connect the shoulder anchor of the front seat outer belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  3. INSTALL CENTER PILLAR GARNISH


    1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH.

    2. A0041KG

      Engage the clip.

    3. Install the center pillar garnish LH with the screw.

  4. INSTALL CENTER PILLAR LOWER GARNISH


    1. Engage the 2 claws and 2 clips to install the center pillar lower garnish LH.

  5. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP

    for LH Side: Click here

    for RH Side: Click here

  6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

    for LH Side: Click here

    for RH Side: Click here

  7. CONNECT FRONT SEAT OUTER BELT ASSEMBLY


    1. A0040I7

      Install the floor end of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  8. INSTALL LAP BELT OUTER ANCHOR COVER


    1. A0041VP

      Engage the 3 claws to install the lap belt outer anchor cover.

  9. INSTALL REAR DOOR SCUFF PLATE


    1. Engage the 7 claws to install the rear door scuff plate LH.

  10. INSTALL FRONT DOOR SCUFF PLATE


    1. Engage the 10 claws to install the front door scuff plate LH.

  11. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. INSTALL REAR NO. 3 FLOOR BOARD UPPER PLATE


    1. Engage the 2 claws to install the rear No. 3 floor board upper plate.

  13. INSTALL DECK FLOOR BOX RH


    1. Install the deck floor box RH Click here.

    2. Install the rear No. 2 floor board.

  14. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  15. INSPECT SRS WARNING LIGHT

    Click here