KNEE AIRBAG ASSEMBLY INSTALLATION


  1. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A0043GGE01
      Text in Illustration
      *1 Airbag Connector
      *2 Airbag Connector Lock

      Connect the airbag connector and engage the clamp to the lower No. 1 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the lock to install the airbag connector.

    5. Temporarily install the lower No. 1 instrument panel airbag assembly with the 6 claws and 4 guides.

    6. Engage the 2 claws to install the DLC3.

    7. Install the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 1 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  2. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. Connect each connector.

    2. Engage the clamp.

    3. Engage the 2 guides and claw to connect the hood lock control cable.

    4. A00412T

      Engage the 6 claws and clip.

    5. Install the lower instrument panel finish panel assembly with the screw <C>.

  3. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. Connect each connector.

    2. Engage the guide and claw.

    3. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <D>.

  4. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Connect each connector.

    2. Engage the guide and 2 claws.

    3. Install the No. 1 instrument panel under cover sub-assembly with the screw <D>.

  5. INSTALL COWL SIDE TRIM BOARD LH


    1. Engage the 2 clips.

    2. Install the cowl side trim board LH with the clip.

  6. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Engage the 10 claws to install the front door scuff plate LH.

  7. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect the connector.

    2. Engage the 5 claws to install the No. 1 switch hole base.

  8. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. Temporarily install the console box assembly.

    2. A0042FY

      Engage the 9 claws as shown in the illustration.

    3. A0041B3

      Install the upper instrument panel finish panel assembly with the 2 bolts <A>.

    4. Engage the clamp.

  9. INSTALL CONSOLE BOX ASSEMBLY


    1. Connect each connector.

    2. A004076

      Engage the 4 guides and 2 claws as shown in the illustration.

    3. Install the console box assembly with the bolt <B> and 2 clips.

  10. INSTALL BOX BOTTOM MAT


    1. Install the box bottom mat.

  11. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    1. A00444WE01

      Engage the guide and 4 claws to install the front No. 2 console box insert as shown in the illustration.

  12. INSTALL CONSOLE BOX INSERT


    1. A00421VE01

      Engage the guide and 4 claws to install the console box insert as shown in the illustration.

  13. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET


    1. Install the No. 2 console box mounting bracket with the 6 bolts <B>.

  14. INSTALL NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY


    1. Engage the clamp and install the No. 1 indoor electrical key antenna assembly.

      Note

      Be careful when installing the No. 1 indoor electrical key antenna assembly. If the No. 1 indoor electrical key antenna assembly is dropped, replace it with a new one.

    2. Connect the connector.

  15. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY


    1. Install the shift lock control unit assembly with the 3 nuts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    2. Connect the connector to the shift lock control unit assembly.

  16. INSTALL AIR CONDITIONING CONTROL ASSEMBLY


    1. Connect the connector.

    2. A0042B3

      Engage the 4 claws to install the air conditioning control assembly.

  17. INSTALL GLOVE COMPARTMENT DOOR


    1. Open the glove compartment door assembly and glove compartment door.

    2. A0040EP

      Insert the glove compartment door as shown in the illustration.

    3. Engage the 7 claws to install the glove compartment door.

  18. INSTALL NO. 2 INSTRUMENT PANEL REGISTER


    1. A00430F

      Engage the 3 claws and clip to install the No. 2 instrument panel register.

  19. INSTALL NO. 1 SIDE DEFROSTER NOZZLE


    1. A00426P

      Engage the 3 claws to install the No. 1 side defroster nozzle.

  20. INSTALL NAVIGATION RECEIVER WITH BRACKET (for Navigation Receiver Type)


    1. Connect each connector.

    2. A0042X9

      Engage the 4 claws and temporarily install the navigation receiver with bracket as shown in the illustration.

    3. Install the navigation receiver with bracket with the 4 bolts.

  21. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)


    1. Connect each connector.

    2. Engage the 4 claws.

    3. Install the radio and display receiver assembly with bracket with the 4 bolts.

  22. INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A0040KM

      Install the radio tuner opening cover with bracket with the 4 bolts <B>.

  23. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver)


    1. A00425U

      Engage the 4 claws to install the center instrument cluster finish panel sub-assembly.

  24. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A0040N0

      Connect the connector.

    2. Engage the 3 claws to install the upper instrument panel finish panel sub-assembly.

  25. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Connect the connector.

    2. Engage the 14 claws to install the instrument cluster finish panel garnish.

  26. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A0040B6

      Engage the 7 claws and 2 clips to install the lower center instrument cluster finish panel sub-assembly.

  27. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A004159

      Connect each connector.

    2. Engage the 6 claws to install the integration control and panel assembly.

  28. INSTALL REAR CONSOLE BOX ASSEMBLY

    Click here

  29. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  30. INSTALL REAR NO. 3 FLOOR BOARD UPPER PLATE


    1. Engage the 2 claws to install the rear No. 3 floor board upper plate.

  31. INSTALL DECK FLOOR BOX RH


    1. Install the deck floor box RH Click here.

    2. Install the rear No. 2 floor board.

  32. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  33. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  34. INSPECT SRS WARNING LIGHT

    Click here