KNEE AIRBAG ASSEMBLY REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE REAR NO. 3 FLOOR BOARD


    1. Remove the rear No. 3 floor board.

  3. REMOVE DECK FLOOR BOX RH


    1. Fold back the rear No. 2 floor board.

    2. Remove the deck floor box RH Click here.

  4. REMOVE REAR NO. 3 FLOOR BOARD UPPER PLATE


    1. A0040W5

      Disengage the 2 claws and remove the rear No. 3 floor board upper plate.

  5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  7. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A00417SE01
      Text in Illustration
      *a Lift slightly

      Using a moulding remover, slightly lift the panel at the position shown in the illustration.

    2. Pull the integration control and panel assembly in the direction indicated by the arrow to disengage the 6 claws.

    3. Disconnect each connector and remove the integration control and panel assembly.

  8. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A0041IM

      Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 2 claws and 2 clips.

    2. A00428K

      Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 5 claws and remove the lower center instrument cluster finish panel sub-assembly.

  9. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Disengage the 14 claws.

      A0042AQ

    2. Disconnect the connector and remove the instrument cluster finish panel garnish.

  10. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A0040N0

      Disengage the 3 claws.

    2. Disconnect the connector and remove the upper instrument panel finish panel sub-assembly.

  11. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver)


    1. A00425U

      Disengage the 4 claws and remove the center instrument cluster finish panel sub-assembly.

  12. REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A0040KM

      Remove the 4 bolts <B> and radio tuner opening cover with bracket.

  13. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)


    1. A0040T3

      Remove the 4 bolts.

    2. A0041HD

      Disengage the 4 claws as shown in the illustration.

    3. Disconnect each connector and remove the radio and display receiver assembly with bracket.

  14. REMOVE NAVIGATION RECEIVER WITH BRACKET (for Navigation Receiver Type)


    1. A0041W7

      Remove the 4 bolts.

    2. A0042NR

      Disengage the 4 claws and remove the navigation receiver with bracket as shown in the illustration.

    3. Disconnect each connector.

  15. REMOVE NO. 1 SIDE DEFROSTER NOZZLE


    1. A0043DQE01
      Text in Illustration
      *a Lift slightly

      Using a moulding remover, slightly lift the panel at the position shown in the illustration.

    2. Pull the No. 1 side defroster nozzle in the direction indicated by the arrow to disengage the 3 claws and remove the No. 1 side defroster nozzle.

  16. REMOVE NO. 2 INSTRUMENT PANEL REGISTER


    1. A004446

      Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the claw and clip.

    2. A004480

      Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the 2 claws and remove the No. 2 instrument panel register.

  17. REMOVE GLOVE COMPARTMENT DOOR


    1. Open the glove compartment door assembly and glove compartment door.

    2. A0040CN

      Pull the glove compartment door in the direction indicated by the arrow to disengage the 7 claws.

    3. Pull the glove compartment door in the direction indicated by the arrow to remove the glove compartment door.

  18. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    1. A00431S

      Disengage the 4 claws and remove the air conditioning control assembly as shown in the illustration.

    2. Disconnect the connector.

  19. REMOVE SHIFT LOCK CONTROL UNIT ASSEMBLY


    1. A0040V3

      Disconnect the connector from the shift lock control unit assembly.

    2. Remove the 3 nuts and shift lock control unit assembly.

  20. REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY


    1. A0043LZ

      Disconnect the connector.

    2. Disengage the clamp and remove the No. 1 indoor electrical key antenna assembly.

      Note

      Be careful when removing the No. 1 indoor electrical key antenna assembly. If the No. 1 indoor electrical key antenna assembly is dropped, replace it with a new one.

  21. REMOVE NO. 2 CONSOLE BOX MOUNTING BRACKET


    1. A0040XU

      Remove the 6 bolts <B> and No. 2 console box mounting bracket.

  22. REMOVE CONSOLE BOX INSERT


    1. A0042UIE01

      Pull the console box insert in the direction indicated by the arrow to disengage the 4 claws and guide, and remove the console box insert.

  23. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. A00411TE01

      Pull the front No. 2 console box insert in the direction indicated by the arrow to disengage the 4 claws and guide, and remove the front No. 2 console box insert.

  24. REMOVE BOX BOTTOM MAT


    1. A0040IE

      Remove the box bottom mat.

  25. SEPARATE CONSOLE BOX ASSEMBLY


    1. A004451

      Remove the bolt <B> and 2 clips.

    2. A0040JK

      While pushing the parts shown in the illustration inward, pull the console box assembly in the direction indicated by the arrow to disengage the 2 claws and 4 guides.

    3. Disconnect the connector and separate the console box assembly.

  26. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A0041B3

      Disengage the clamp.

    2. Remove the 2 bolts <A>.

    3. A00446C

      Pull the upper instrument panel finish panel assembly in the direction indicated by the arrow to disengage the 9 claws and remove the upper instrument panel finish panel assembly.

  27. REMOVE CONSOLE BOX ASSEMBLY


    1. A0043QZ

      Remove the console box assembly.

  28. REMOVE NO. 1 SWITCH HOLE BASE


    1. A0042DK

      Disengage the 5 claws.

    2. Disconnect the connector to remove the No. 1 switch hole base.

  29. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A0042VN

      Disengage the 10 claws and remove the front door scuff plate LH.

  30. REMOVE COWL SIDE TRIM BOARD LH


    1. A0042AR

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim board LH.

  31. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. A00420O

      Remove the 2 screws <D>.

    2. Disengage the claw and guide.

    3. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  32. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A0042XI

      Remove the screw <D>.

    2. Disengage the 2 claws and guide.

    3. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  33. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A0041MT

      Remove the screw <C>.

    2. A00438O

      Disengage the 6 claws and clip as shown in the illustration.

    3. A00436H

      Disengage the claw and 2 guides and disconnect the hood lock control cable.

    4. Disconnect each connector and clamp, and remove the lower instrument panel finish panel assembly.

  34. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    CAUTION:

    When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A004375

      Remove the 4 bolts.

    4. Disengage the 2 claws to disconnect the DLC3.

    5. A00408Z

      Disengage the 6 claws and 4 guides to separate the lower No. 1 instrument panel airbag assembly.

      Note

      When removing the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.

    6. A0042X0E02
      Text in Illustration
      *1 Protective Tape
      *2 Airbag Connector
      *3 Airbag Connector Lock

      Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.

    7. Disconnect the clamp and airbag connector to remove the lower No. 1 instrument panel airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.