SPIRAL CABLE INSPECTION

INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

1. Visually check for defects with the spiral cable with sensor sub-assembly removed from the vehicle.

   
   

   1. The defects are as follows:

      
      

      • Scratches

      • Small cracks

      • Dents

      • Chips

      • Cracks or other damage to the connector

        OK
        No defects are found.

      If any of the defects is found, replace the spiral cable with sensor sub-assembly with a new one.

2. 

   Text in Illustration

   *a	Component without harness connected (Spiral Cable with Sensor Sub-assembly)

   Check the spiral cable with sensor sub-assembly.

   Note

   As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.

   
   

   1. Set the spiral cable with sensor sub-assembly to the center position Click here.

   2. Measure the resistance between each terminal of the spiral cable with sensor sub-assembly according to the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition L43-1 (CCS) - z10-3 Always 3 Ω or less L43-2 (ECC) - z10-4 Always 3 Ω or less L43-2 (ECC) - z9-6 Always 3 Ω or less L43-3 (TX1) - z9-7 Always 3 Ω or less L43-4 (EAU) - z9-8 Always 3 Ω or less L43-5 (AU2) - z9-9 Always 3 Ω or less L43-6 (AU1) - z9-10 Always 3 Ω or less L43-7 (R/N) - z10-1 Always 3 Ω or less L43-8 (HO) - z9-1 Always 3 Ω or less L43-9 (IG) - z9-2 Always 3 Ω or less L43-10 (AC1) - z9-3 Always 3 Ω or less L43-11 (DIST) - z9-4 Always 3 Ω or less L43-12 (IL+2) - z9-5 Always 3 Ω or less L44-1 (D+) - z8-2 Always Below 1 Ω L44-2 (D-) - z8-1 Always Below 1 Ω

   3. After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable with sensor sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition L43-1 (CCS) - z10-3 Always 3 Ω or less L43-2 (ECC) - z10-4 Always 3 Ω or less L43-2 (ECC) - z9-6 Always 3 Ω or less L43-3 (TX1) - z9-7 Always 3 Ω or less L43-4 (EAU) - z9-8 Always 3 Ω or less L43-5 (AU2) - z9-9 Always 3 Ω or less L43-6 (AU1) - z9-10 Always 3 Ω or less L43-7 (R/N) - z10-1 Always 3 Ω or less L43-8 (HO) - z9-1 Always 3 Ω or less L43-9 (IG) - z9-2 Always 3 Ω or less L43-10 (AC1) - z9-3 Always 3 Ω or less L43-11 (DIST) - z9-4 Always 3 Ω or less L43-12 (IL+2) - z9-5 Always 3 Ω or less L44-1 (D+) - z8-2 Always Below 1 Ω L44-2 (D-) - z8-1 Always Below 1 Ω

   4. After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition L43-1 (CCS) - z10-3 Always 3 Ω or less L43-2 (ECC) - z10-4 Always 3 Ω or less L43-2 (ECC) - z9-6 Always 3 Ω or less L43-3 (TX1) - z9-7 Always 3 Ω or less L43-4 (EAU) - z9-8 Always 3 Ω or less L43-5 (AU2) - z9-9 Always 3 Ω or less L43-6 (AU1) - z9-10 Always 3 Ω or less L43-7 (R/N) - z10-1 Always 3 Ω or less L43-8 (HO) - z9-1 Always 3 Ω or less L43-9 (IG) - z9-2 Always 3 Ω or less L43-10 (AC1) - z9-3 Always 3 Ω or less L43-11 (DIST) - z9-4 Always 3 Ω or less L43-12 (IL+2) - z9-5 Always 3 Ω or less L44-1 (D+) - z8-2 Always Below 1 Ω L44-2 (D-) - z8-1 Always Below 1 Ω

      If the result is not as specified, replace the spiral cable with sensor sub-assembly.