POWER DOOR LOCK CONTROL SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body or Master Switch / Data List.

    5. Read the Data List according to the display on the GTS.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RR Door Courtesy SW Rear door courtesy light switch RH and LH signal/ON or OFF

      ON: Rear door RH or LH open

      OFF: Rear door RH and LH closed

      		 -
      RL Door Courtesy SW Rear door courtesy light switch RH and LH signal/ON or OFF

      ON: Rear door RH or LH open

      OFF: Rear door RH and LH closed

      		 -
      Back Door Courtesy SW Back door courtesy switch signal/ ON or OFF

      ON: Back door open

      OFF: Back door closed

      		 -
      Back Door Open Back door lock/Permit or Prohibt

      Permit: Back door unlocked

      Prohibt: Back door locked

      		 -
      Door Key SW-Lock Driver door key-linked lock/unlock switch lock signal/ON or OFF

      ON: Driver door key cylinder turned to lock position

      OFF: Driver door key cylinder not turned to lock position

      		 -
      Door Key SW-Unlock Driver door key-linked lock/unlock switch unlock signal/ON or OFF

      ON: Driver door key cylinder turned to unlock position

      OFF: Driver door key cylinder not turned to unlock position

      		 -
      FR Door Lock Pos Front door RH unlock detection switch signal/LOCK or UNLOCK

      LOCK: Front door RH locked

      UNLOCK: Front door RH unlocked

      		 -
      FR Door Courtesy SW Front door courtesy light switch RH signal/ON or OFF

      ON: Front door RH open

      OFF: Front door RH closed

      		 -
      FL Door Lock Pos Front door LH unlock detection switch signal/LOCK or UNLOCK

      LOCK: Front door LH locked

      UNLOCK: Front door LH unlocked

      		 -
      FL Door Courtesy SW Front door courtesy light switch LH signal/ON or OFF

      ON: Front door LH open

      OFF: Front door LH closed

      		 -
      Back Door Open Handle SW*1 Back door opener switch signal/ ON or OFF

      ON: Back door opener switch pushed

      OFF: Back door opener switch not pushed

      		 -
      RR-Door Lock Pos SW*2 Rear door RH and LH unlock detection switch signal/ON or OFF

      ON: Rear door RH or LH unlocked

      OFF: Rear door RH and LH locked

      		 -
      RL-Door Lock Pos SW*3 Rear door RH and LH unlock detection switch signal/ON or OFF

      ON: Rear door RH or LH unlocked

      OFF: Rear door RH and LH locked

      		 -

      • *1: w/o Entry System Back Door Open Function

      • *2: When checking RR-Door Lock Pos SW, make sure to check it with the rear door LH locked.

      • *3: When checking RL-Door Lock Pos SW, make sure to check it with the rear door RH locked.

      Master Switch
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Door Lock Switch Status Driver door control switch lock signal/ON or OFF

      ON: Lock side of driver door control switch pushed

      OFF: Lock side of driver door control switch not pushed

      		 -
      Door Unlock Switch Status Driver door control switch unlock signal/ON or OFF

      ON: Unlock side of driver door control switch pushed

      OFF: Unlock side of driver door control switch not pushed

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Main Body (Main Body ECU (Multiplex Network Body ECU))
      Tester Display Test Part Control Range Diagnostic Note
      Door Lock Door lock motor Unlock/Lock -
      Trunk and Back-Door Open Back door lock motor OFF/ON -