PARKING ASSIST PRE SUPPORT SWITCH INSTALLATION


  1. INSTALL PARKING ASSIST PRE SUPPORT SWITCH


    1. Engage the 2 claws to install the parking assist pre support switch.

  2. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect the connector.

    2. Engage the 5 claws to install the No. 1 switch hole base.

  3. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. Temporarily install the console box assembly.

    2. A0042FY

      Engage the 9 claws as shown in the illustration.

    3. A0041B3

      Install the upper instrument panel finish panel assembly with the 2 bolts <A>.

    4. Engage the clamp.

  4. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY


    1. Install the shift lock control unit assembly with the 3 nuts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    2. Connect the connector to the shift lock control unit assembly.

  5. INSTALL AIR CONDITIONING CONTROL ASSEMBLY


    1. Connect the connector.

    2. A0042B3

      Engage the 4 claws to install the air conditioning control assembly.

  6. INSTALL CONSOLE BOX ASSEMBLY


    1. Connect each connector.

    2. A004076

      Engage the 4 guides and 2 claws as shown in the illustration.

    3. Install the console box assembly with the bolt <B> and 2 clips.

  7. INSTALL BOX BOTTOM MAT


    1. Install the box bottom mat.

  8. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    1. A00444WE01

      Engage the guide and 4 claws to install the front No. 2 console box insert as shown in the illustration.

  9. INSTALL CONSOLE BOX INSERT


    1. A00421VE01

      Engage the guide and 4 claws to install the console box insert as shown in the illustration.

  10. INSTALL NO. 2 CONSOLE BOX MOUNTING BRACKET


    1. Install the No. 2 console box mounting bracket with the 6 bolts <B>.

  11. INSTALL NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY


    1. Engage the clamp and install the No. 1 indoor electrical key antenna assembly.

      Note

      Be careful when installing the No. 1 indoor electrical key antenna assembly. If the No. 1 indoor electrical key antenna assembly is dropped, replace it with a new one.

    2. Connect the connector.

  12. INSTALL REAR CONSOLE BOX ASSEMBLY


    1. Connect each connector.

    2. A0040HR

      Engage the 8 claws as shown in the illustration.

    3. Install the rear console box assembly with the 5 bolts.

  13. INSTALL CONSOLE BOX CARPET


    1. Install the console box carpet.

  14. INSTALL REAR CONSOLE BOX CUP HOLDER


    1. A0043UQ

      Engage the 4 claws to install the rear console box cup holder as shown in the illustration.

  15. INSTALL NAVIGATION RECEIVER WITH BRACKET


    1. Connect each connector.

    2. A0042X9

      Engage the 4 claws and temporarily install the navigation receiver with bracket as shown in the illustration.

    3. Install the navigation receiver with bracket with the 4 bolts.

  16. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A0040N0

      Connect the connector.

    2. Engage the 3 claws to install the upper instrument panel finish panel sub-assembly.

  17. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Connect the connector.

    2. Engage the 14 claws to install the instrument cluster finish panel garnish.

  18. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A0040B6

      Engage the 7 claws and 2 clips to install the lower center instrument cluster finish panel sub-assembly.

  19. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A004159

      Connect each connector.

    2. Engage the 6 claws to install the integration control and panel assembly.

  20. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  21. INSTALL REAR NO. 3 FLOOR BOARD UPPER PLATE


    1. Engage the 2 claws to install the rear No. 3 floor board upper plate.

  22. INSTALL DECK FLOOR BOX RH


    1. Install the deck floor box RH Click here.

    2. Install the rear No. 2 floor board.

  23. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  24. INSPECT SHIFT LEVER


    1. Turn the power switch on (READY).

    2. Check that all available shift positions can be selected moving the shift lever.

      Tech Tips

      After the shift lock control unit assembly is replaced with a new one, perform the above operation. If this operation is not performed, moving the shift lever may not initially select shift positions.