CHARGE INDICATOR INSTALLATION


  1. INSTALL INDICATOR LAMP ASSEMBLY


    1. Install the indicator lamp with the 3 screws.

    2. Connect the connector.

  2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Engage the 7 claws and 2 clips.

    2. Install the deck trim side panel assembly RH with the screw.

  3. INSTALL TONNEAU COVER HOLDER CAP (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side Click here.

  4. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure described for the LH side Click here.

  5. INSTALL REAR SIDE SEAT BACK ASSEMBLY RH


    1. A0043VX

      Engage the 2 guides as shown in the illustration.

    2. Engage the 3 fasteners.

    3. Install the rear side seatback assembly RH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  6. INSTALL REAR SEAT CUSHION ASSEMBLY


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. A0042WJE01
      Text in Illustration
      *1 Rear Hook
      *2 Front Hook

      Engage the 2 rear hooks of the rear seat cushion assembly to the rear seatback assembly.

    3. Engage the 2 front hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

    4. Confirm that the rear seat cushion assembly is firmly installed.

      Note

      When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.

  7. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. A0041Y8E01
      Text in Illustration
      *1 Alignment Mark (Blue)

      Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  8. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side Click here.

  9. INSTALL REAR DECK TRIM COVER


    1. Engage the 4 claws to install the rear deck trim cover.

  10. INSTALL DECK TRIM SERVICE HOLE COVER


    1. Engage the 4 guides.

    2. Engage the 4 claws to install the deck trim service hole cover.

  11. INSTALL REAR NO. 1 FLOOR BOARD


    1. Engage the 3 fasteners.

    2. Install the rear No. 1 floor board with the clip.

    3. Engage each fastener.

  12. INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    1. Engage the claw and 3 clips to install the rear No. 1 floor board sub-assembly.

  13. INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    1. Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.

  14. INSTALL TONNEAU COVER ASSEMBLY


    1. Install the tonneau cover assembly.

  15. INSTALL DECK FLOOR BOX LH

    Tech Tips

    Use the same procedure described for the RH side.

  16. INSTALL REAR NO. 4 FLOOR BOARD SUB-ASSEMBLY


    1. Install the rear No. 4 floor board sub-assembly.

  17. INSTALL DECK FLOOR BOX RH


    1. Engage the claw and 4 guide to install the deck floor box RH.

  18. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  19. INSTALL REAR NO. 2 FLOOR BOARD


    1. Engage the 3 fasteners.

    2. Install the rear No. 2 floor board with the 2 clips.