HYBRID CONTROL SYSTEM, Diagnostic DTC:P3000-388

DTC Code DTC Name
P3000-388 HV Battery Malfunction

DESCRIPTION

The power management control ECU alerts the driver and performs fail-safe control based on error signals received from the battery smart unit. This DTC is set when the SOC (state of charge) of the HV battery starts to drop as a result of leaving the shift lever in N, running out of fuel, or a malfunction in the hybrid control system.

DTC No. INF Code DTC Detection Condition Trouble Area
P3000 388 Discharge inhibition control malfunction

  • Fuel level

  • HV battery

INSPECTION PROCEDURE

Tech Tips


  • If the vehicle is stopped or parked with the shift lever in the N position for a long time, DTC P3000-388 may be set because the HV battery cannot be charged.

  • When the engine cannot be started, DTC P3000-388 may be set because the HV battery cannot be charged.

  • If engine start inspection is performed repeatedly, DTC P3000-388 may be output due to the SOC of the battery dropping. In this case, plug-in charge the HV battery.

  • Cranking the engine once causes the SOC to drop approximately 0.5 %.

  • When plug-in charging the vehicle for 10 minutes using AC 100 V, the SOC of connecting pack will increase by approximately 3.5 %. If AC 200 V is used, the SOC will increase by approximately 7 %.

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      P3000-388 or P3000-389 only is output. A
      DTCs other than P3000-388 and P3000-389 are also output. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    A

  2. CHECK DTC OUTPUT (ENGINE AND ECT)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      NO DTCs are output. A
      DTCs are output. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (SFI SYSTEM) Click here

    A

  3. CHECK AMOUNT OF FUEL


    1. Turn the power switch on (IG).

    2. Check the amount of fuel by referring to the fuel gauge in the meter.

      Result
      Result Proceed to
      Proper amount of fuel is in the tank. A
      There is no fuel in the tank. B

      Tech Tips

      Add fuel until the low fuel level warning light turns off.

    3. Turn the power switch off.


    B

    REFUEL VEHICLE

    A

  4. CHECK ENGINE START


    1. Turn the power switch on (READY).

    2. Check if the engine starts.

      Tech Tips


      • Depressing the accelerator pedal with the park (P) selected will cause the engine to start.

      • Turning the power switch on (READY) and off repeatedly while the SOC is low may cause the SOC to drop further, resulting in DTC P3000-389 being set. Charge the plug-in charge the HV battery as necessary.

      • Cranking the engine once causes the SOC to drop approximately 0.5 %.

      • When plug-in charging the vehicle for 10 minutes using AC 100 V, the SOC of connecting pack will increase by approximately 3.5 %. If AC 200 V is used, the SOC will increase by approximately 7 %.

      Result
      Result Proceed to
      The engine starts. A
      The engine does not start. B

    3. If the engine does not start, turn the power switch off.


    B

    CHARGE HV BATTERY (PLUG IN (CHECK THAT ENGINE STARTS))

    A

    LEAVE VEHICLE WITH PARK (P) SELECTED, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS