HYBRID CONTROL SYSTEM, Diagnostic DTC:P082B-575, P082C-576, P082E-571, P082F-572, P181A-596, P181B-595, P182B-577, P182C-578, P182E-573, P182F-574
| DTC Code | DTC Name |
|---|---|
| P082B-575 | Gear Lever X Position Circuit Low |
| P082C-576 | Gear Lever X Position Circuit High |
| P082E-571 | Gear Lever Y Position Circuit Low |
| P082F-572 | Gear Lever Y Position Circuit High |
| P181A-596 | Gear Lever X Position Circuit "A" / "B" Correlation |
| P181B-595 | Gear Lever Y Position Circuit "A" / "B" Correlation |
| P182B-577 | Gear Lever X Position "B" Circuit Low |
| P182C-578 | Gear Lever X Position "B" Circuit High |
| P182E-573 | Gear Lever Y Position "B" Circuit Low |
| P182F-574 | Gear Lever Y Position "B" Circuit High |
DESCRIPTION
Tech Tips
-
The electronic shift lever system is a linkless type that does not use a shift cable.
-
The shift and select sensors are non-contact type sensors.
-
The shift lever (shift lock control unit assembly) is a momentary type, which returns to its home position by spring reaction as the driver's hand is released from the shift lever after shifting.
The shift lever (shift lock control unit assembly) contains a shift sensor and a select sensor to detect the shift lever position (Home, R, N, D or B). Because the shift sensor operates using Hall ICs and the select sensor operates using MR ICs, they can accurately detect the shift lever position in a reliable manner. Both sensors contain two detection circuits, a main and a sub circuit.
-
The shift sensor outputs voltage, which varies between 0 and 5 V in accordance with the vertical movement of the shift lever, to the power management control ECU. The power management control ECU interprets low level voltage input from the shift sensor as the R position, middle level voltage as the home or N position, and high level voltage as the D or B position.
-
The select sensor outputs voltage, which varies between 0 and 5 V in accordance with the horizontal movement of the shift lever, to the power management control ECU. The power management control ECU interprets low level voltage input from the select sensor as the home or B position, and high level voltage as the R, N, or D position.
The power management control ECU determines the position of the shift lever in accordance with the combination of the signals from the shift sensor and select sensor.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P082B | 575 | Open or GND short in select main sensor circuit |
|
| P082C | 576 | +B short in select main sensor circuit | |
| P082E | 571 | Open or GND short in shift main sensor circuit | |
| P082F | 572 | +B short in shift main sensor circuit | |
| P181A | 596 | Difference between select main sensor value and select sub sensor value is large | |
| P181B | 595 | Difference between shift main sensor value and shift sub sensor value is large | |
| P182B | 577 | Open or GND short in select sub sensor circuit | |
| P182C | 578 | +B short in select sub sensor circuit | |
| P182E | 573 | Open or GND short in shift sub sensor circuit | |
| P182F | 574 | +B short in shift sub sensor circuit |
Tech Tips
When any of DTCs P082E-571, P082F-572, P182E-573 or P182F-574 are output, check Shift Sensor Main and Shift Sensor Sub voltages using the GTS.
| R position (Main) |
Home or N position (Main) |
D or B position (Main) |
R position (Sub) |
Home or N position (Sub) |
D or B position (Sub) |
Trouble Area |
|---|---|---|---|---|---|---|
| 0.3 to 1.8 V | 2.0 to 3.0 V | 3.2 to 4.8 V | 0.3 to 1.8 V | 2.0 to 3.0 V | 3.2 to 4.8 V | Correct shift sensor voltage |
| 0 to 0.3 V | 0 to 0.3 V | 0 to 0.3 V | 0.3 to 1.8 V | 2.0 to 3.0 V | 3.2 to 4.8 V | Open in VCX1 circuit GND short in VSX1 circuit |
| 0.3 to 1.8 V | 2.0 to 3.0 V | 3.2 to 4.8 V | 0 to 0.3 V | 0 to 0.3 V | 0 to 0.3 V | Open in VCX2 circuit GND short in VSX2 circuit |
| 4.8 to 5.0 V | 4.8 to 5.0 V | 4.8 to 5.0 V | 0.3 to 1.8 V | 2.0 to 3.0 V | 3.2 to 4.8 V | Open in VSX1 circuit Open in E2X1 circuit |
| 0.3 to 1.8 V | 2.0 to 3.0 V | 3.2 to 4.8 V | 4.8 to 5.0 V | 4.8 to 5.0 V | 4.8 to 5.0 V | Open in VSX2 circuit Open in E2X2 circuit |
Tech Tips
When any of DTCs P082B-575, P082C-576, P182B-577 or P182C-578 are output, check Shift Sensor Select Main and Shift Sensor Select Sub voltages using the GTS.
| R, N or D Position Select Main) |
Home or B Position Select Main) |
R, N or D Position Select Sub) |
Home or B Position Select Sub) |
Trouble Area |
|---|---|---|---|---|
| 2.9 to 4.3 V | 1.0 to 1.6 V | 2.9 to 4.3 V | 1.0 to 1.6 V | Correct select sensor voltage |
| 0 to 0.5 V | 0 to 0.5 V | 2.9 to 4.3 V | 1.0 to 1.6 V | Open in VCX3 circuit Open or GND short in VSX3 circuit |
| 2.9 to 4.3 V | 1.0 to 1.6 V | 0 to 0.5 V | 0 to 0.5 V | Open in VCX4 circuit Open or GND short in VSX4 circuit |
| 4.9 to 5.0 V | 4.9 to 5.0 V | 2.9 to 4.3 V | 1.0 to 1.6 V | +B short in VSX3 circuit |
| 2.9 to 4.3 V | 1.0 to 1.6 V | 4.9 to 5.0 V | 4.9 to 5.0 V | +B short in VSX4 circuit |
INSPECTION PROCEDURE
PROCEDURE
-
READ VALUE USING GTS (SHIFT SENSOR MAIN, SHIFT SENSOR SUB)
-
Connect the GTS to the DLC3.
-
Turn the power switch on (IG).
-
Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Sensor Main, Shift Sensor Sub.
-
Read the Data List.
Result Tester Display Condition Specified Condition Shift Sensor Main R position 0.3 to 1.8 V Home or N position 2.0 to 3.0 V D or B position 3.2 to 4.8 V Shift Sensor Sub R position 0.3 to 1.8 V Home or N position 2.0 to 3.0 V D or B position 3.2 to 4.8 V -
Turn the power switch off.
NG 
CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - SHIFT SENSOR) Click here
OK 
-
-
READ VALUE USING GTS (SHIFT SENSOR SELECT MAIN, SHIFT SENSOR SELECT SUB)
-
Connect the GTS to the DLC3.
-
Turn the power switch on (IG).
-
Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Sensor Select Main, Shift Sensor Select Sub.
-
Read the Data List.
Result Tester Display Condition Specified Condition Shift Sensor Select Main R, N or D Position 2.9 to 4.3 V Home or B Position 1.0 to 1.6 V Shift Sensor Select Sub R, N or D Position 2.9 to 4.3 V Home or B Position 1.0 to 1.6 V -
Turn the power switch off.
NG
CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - SELECT SENSOR) Click here
OK
-
-
REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY
NEXT
-
CLEAR DTC
-
Connect the GTS to the DLC3.
-
Turn the power switch on (IG).
-
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
-
Read and record the DTCs and freeze frame data.
-
Clear DTCs and freeze frame data.
-
Turn the power switch off.
NEXT
-
-
CHECK DTC OUTPUT (HYBRID CONTROL)
-
Connect the GTS to the DLC3.
-
Turn the power switch on (IG).
-
With the brake pedal depressed, slowly move the shift lever as follows to select each shift state: N → R → N → D → B.
-
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
-
Check if DTCs are output.
Result Result Proceed to No DTCs are output. A P082B-575, P082C-576, P082E-571, P082F-572, P181A-596, P181B-595, P182B-577, P182C-578, P182E-573 or P182F-574 is output again. B -
Turn the power switch off.
B 
REPLACE POWER MANAGEMENT CONTROL ECU Click here
A 
COMPLETED
-
-
CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - SHIFT SENSOR)
-
Disconnect the L5 power management control ECU connector.
-
Disconnect the z6 shift sensor connector.
-
Text in Illustration *a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Shift Sensor)
Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open) Tester Connection Condition Specified Condition L5-26 (VCX1) - z6-3 (VCX1) Power switch off Below 1 Ω L5-25 (VSX1) - z6-1 (VSX1) Power switch off Below 1 Ω L5-24 (E2X1) - z6-2 (E2X1) Power switch off Below 1 Ω L5-21 (VCX2) - z6-6 (VCX2) Power switch off Below 1 Ω L5-22 (VSX2) - z6-4 (VSX2) Power switch off Below 1 Ω L5-23 (E2X2) - z6-5 (E2X2) Power switch off Below 1 Ω Standard Resistance (Check for Short) Tester Connection Condition Specified Condition L5-26 (VCX1) or z6-3 (VCX1) - Body ground and other terminals Power switch off 10 kΩ or higher L5-25 (VSX1) or z6-1 (VSX1) - Body ground and other terminals Power switch off 10 kΩ or higher L5-24 (E2X1) or z6-2 (E2X1) - Body ground and other terminals Power switch off 10 kΩ or higher L5-21 (VCX2) or z6-6 (VCX2) - Body ground and other terminals Power switch off 10 kΩ or higher L5-22 (VSX2) or z6-4 (VSX2) - Body ground and other terminals Power switch off 10 kΩ or higher L5-23 (E2X2) or z6-5 (E2X2) - Body ground and other terminals Power switch off 10 kΩ or higher Tech Tips
As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.
-
Reconnect the z6 shift sensor connector.
-
Reconnect the L5 power management control ECU connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
-
-
CHECK POWER MANAGEMENT CONTROL ECU (VCX1, VCX2 VOLTAGE)
-
Disconnect the z6 shift sensor connector.
-
Turn the power switch on (IG).
-
Text in Illustration *a Front view of wire harness connector
(to Shift Sensor)
Measure the voltage according to the value(s) in the table below.
Standard Voltage Tester Connection Condition Specified Condition z6-3 (VCX1) - z6-2 (E2X1) Power switch on (IG) 4.5 to 5.5 V z6-6 (VCX2) - z6-5 (E2X2) Power switch on (IG) 4.5 to 5.5 V Note
Turning the power switch on (IG) with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
-
Turn the power switch off.
-
Reconnect the z6 shift sensor connector.
NG
REPLACE POWER MANAGEMENT CONTROL ECU Click here
OK
-
-
REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY
NEXT
-
CLEAR DTC
-
Connect the GTS to the DLC3.
-
Turn the power switch on (IG).
-
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
-
Read and record the DTCs and freeze frame data.
-
Clear DTCs and freeze frame data.
-
Turn the power switch off.
NEXT
-
-
CHECK DTC OUTPUT (HYBRID CONTROL)
-
Connect the GTS to the DLC3.
-
Turn the power switch on (IG).
-
With the brake pedal depressed, slowly move the shift lever as follows to select each shift state: N → R → N → D → B.
-
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
-
Check if DTCs are output.
Result Result Proceed to No DTCs are output. A P082B-575, P082C-576, P082E-571, P082F-572, P181A-596, P181B-595, P182B-577, P182C-578, P182E-573 or P182F-574 is output again. B -
Turn the power switch off.
B
REPLACE POWER MANAGEMENT CONTROL ECU Click here
A
COMPLETED
-
-
CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - SELECT SENSOR)
-
Disconnect the L5 power management control ECU connector.
-
Disconnect the z5 select sensor connector.
-
Text in Illustration *a Rear view of wire harness connector:
(to Power Management Control ECU)
*b Front view of wire harness connector:
(to Select Sensor)
Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open) Tester Connection Condition Specified Condition L5-19 (VCX3) - z5-5 (VCX3) Power switch off Below 1 Ω L5-20 (VSX3) - z5-4 (VSX3) Power switch off Below 1 Ω L5-17 (VCX4) - z5-2 (VCX4) Power switch off Below 1 Ω L5-18 (VSX4) - z5-1 (VSX4) Power switch off Below 1 Ω Standard Resistance (Check for Short) Tester Connection Condition Specified Condition L5-19 (VCX3) or z5-5 (VCX3) - Body ground and other terminals Power switch off 10 kΩ or higher L5-20 (VSX3) or z5-4 (VSX3) - Body ground and other terminals Power switch off 10 kΩ or higher L5-17 (VCX4) or z5-2 (VCX4) - Body ground and other terminals Power switch off 10 kΩ or higher L5-18 (VSX4) or z5-1 (VSX4) - Body ground and other terminals Power switch off 10 kΩ or higher Tech Tips
As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.
-
Reconnect the z5 select sensor connector.
-
Reconnect the L5 power management control ECU connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
-
-
CHECK POWER MANAGEMENT CONTROL ECU (VCX3, VCX4 VOLTAGE)
-
Disconnect the z5 select sensor connector.
-
Turn the power switch on (IG).
-
Text in Illustration *a Front view of wire harness connector:
(to Select Sensor)
Measure the voltage according to the value(s) in the table below.
Standard Voltage Tester Connection Condition Specified Condition z5-5 (VCX3) - Body ground Power switch on (IG) 9 to 14 V z5-2 (VCX4) - Body ground Power switch on (IG) 9 to 14 V Note
Turning the power switch on (IG) with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
-
Turn the power switch off.
-
Reconnect the z5 select sensor connector.
NG
REPLACE POWER MANAGEMENT CONTROL ECU Click here
OK
-
-
REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY
NEXT
-
CLEAR DTC
-
Connect the GTS to the DLC3.
-
Turn the power switch on (IG).
-
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
-
Read and record the DTCs and freeze frame data.
-
Clear DTCs and freeze frame data.
-
Turn the power switch off.
NEXT
-
-
CHECK DTC OUTPUT (HYBRID CONTROL)
-
Connect the GTS to the DLC3.
-
Turn the power switch on (IG).
-
With the brake pedal depressed, slowly move the shift lever as follows to select each shift state: N → R → N → D → B.
-
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
-
Check if DTCs are output.
Result Result Proceed to No DTCs are output. A P082B-575, P082C-576, P082E-571, P082F-572, P181A-596, P181B-595, P182B-577, P182C-578, P182E-573 or P182F-574 is output again. B -
Turn the power switch off.
B
REPLACE POWER MANAGEMENT CONTROL ECU Click here
A
COMPLETED
-