REPAIR INSTRUCTION CUSTOMIZE PARAMETERS


  1. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS


      1. Connect the GTS.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Wireless Door Lock.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Wireless Control ON Function that turns wireless door lock/ON or OFF ON or OFF Main body ECU (Multiplex network body ECU)
        Hazard Answer Back ON

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 ON or OFF Main body ECU (Multiplex network body ECU)
        Open Door Warning ON The buzzer sounds when lock is pressed when any of the doors are ajar. ON or OFF Main body ECU (Multiplex network body ECU)
        Panic Function*1 ON Function to operate theft deterrent system by continuously pressing panic switch on electrical key transmitter sub-assembly for 0.8 seconds ON or OFF Main body ECU (Multiplex network body ECU)
        Auto Lock Time 30 s Function that regulates the interval between unlocking and automatic relocking of doors 30 s, 60 s or 120 s Main body ECU (Multiplex network body ECU)
        Wireless Buzzer Resp*2 ON Wireless door lock buzzer response/ON or OFF ON or OFF Main body ECU (Multiplex network body ECU)
        Wireless Buzzer Vol Level 7 Wireless door lock buzzer volume Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level 0 Main body ECU (Multiplex network body ECU)

        • *1: w/ Panic Function

        • *2: w/ Wireless Buzzer Answer Back Function

    2. Customizing with the Multi-display (for Navigation Receiver Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Door Lock Setting.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Lock/Unlock Feedback-Lights On

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 On or Off Main body ECU (Multiplex network body ECU)
        Lock Feedback Volume 7 Wireless door lock buzzer volume 0, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU)

    3. Customizing with the Multi-display (for Radio and Display Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Lock Feedback Volume 7 Wireless door lock buzzer volume 0, 1, 2, 3, 4, 5, 6 or 7 Main body ECU (Multiplex network body ECU)

  2. CUSTOMIZE ENTRY AND START SYSTEM (for Entry Function)

    Tech Tips

    The items in the table below can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current setting before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting.

      5. Select the setting by referring to the table below.

        Entry & Start
        Tester Display Default Content Setting Relevant ECU
        Park Wait Time 2.5 s Function that sets waiting time to permit opening door after door is locked with entry lock function 0.5 s, 1.5 s, 2.5 s or 5 s Certification ECU (smart key ECU assembly)
        Ignition Available Area All Function that switches the entry hybrid control system start detection area Front or All*1 Certification ECU (smart key ECU assembly)
        Back Door Opening Operation*2 Long Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch) Long, Twice or OFF Certification ECU (smart key ECU assembly)
        Auto Entry Cancel SW OFF Function that enables or disables the entry and start system. ON or OFF Certification ECU (smart key ECU assembly)

        Tech Tips


        • *1: Weak radio waves will still be emitted from antennas other than the front antenna even when the "Front" customize setting is selected.

        • *2: w/ Entry Back Door Open Function

        Warning
        Tester Display Default Content Setting Relevant ECU
        Key Low Battery Warning ON Function that warns driver that the key battery is weak ON or OFF Certification ECU (smart key ECU assembly)

    2. Customizing with the multi-display (for Navigation Receiver Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Setting.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and start system On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

    3. Customizing with the multi-display ( for Radio and Display Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and start system On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

    4. Entry cancel function (manual operation).

      The electrical key cancel operation disables the following functions:


      • Entry Unlock/Lock

      • Entry Hybrid Control System Start

      • Entry System Back Door Open Function

      • Key Lock-in Prevention

      • Warning


      1. The operation procedure is as follows:

        Precondition:

        Power switch off, driver door closed and unlocked.


        1. Push the unlock switch of the key once.

        2. Open the driver door within 5 seconds.

        3. Push the unlock switch of the key twice within 5 seconds.

        4. Close and open the driver door twice within 30 seconds.

          (Driver door: Close → Open → Close → Open)

        5. Push the unlock switch of the key twice within 5 seconds.

        6. Close and open the driver door within 30 seconds.

          (Driver door: Close → Open)

        7. Close the driver door within 5 seconds.

          When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

          To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.

  3. CUSTOMIZE ENTRY AND START SYSTEM (for Start Function)

    Tech Tips

    The items in the table below can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current setting before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting.

      5. Select the setting by referring to the table below.

        Entry & Start
        Tester Display Default Content Setting Relevant ECU
        Ignition Available Area All Function that switches the entry hybrid control system start detection area Front or All* Certification ECU (smart key ECU assembly)
        Auto Entry Cancel SW OFF Function that enables or disables the entry and start system. ON or OFF Certification ECU (smart key ECU assembly)

        Tech Tips

        *: Weak radio waves will still be emitted from antennas other than the front antenna even when the "Front" customize setting is selected.

        Warning
        Tester Display Default Content Setting Relevant ECU
        Key Low Battery Warning ON Function that warns driver that the key battery is weak ON or OFF Certification ECU (smart key ECU assembly)

    2. Customizing with the multi-display (for Navigation Receiver Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Setting.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and start system On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

    3. Customizing with the multi-display ( for Radio and Display Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and start system On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

    4. Entry cancel function (manual operation).

      The electrical key cancel operation disables the following functions:


      • Entry Unlock/Lock

      • Entry Hybrid Control System Start

      • Entry System Back Door Open Function

      • Key Lock-in Prevention

      • Warning


      1. The operation procedure is as follows:

        Precondition:

        Power switch off, driver door closed and unlocked.


        1. Push the unlock switch of the key once.

        2. Open the driver door within 5 seconds.

        3. Push the unlock switch of the key twice within 5 seconds.

        4. Close and open the driver door twice within 30 seconds.

          (Driver door: Close → Open → Close → Open)

        5. Push the unlock switch of the key twice within 5 seconds.

        6. Close and open the driver door within 30 seconds.

          (Driver door: Close → Open)

        7. Close the driver door within 5 seconds.

          When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

          To return to the original condition, perform the procedure again. When the original condition is returned, the wireless door lock buzzer sounds once.

  4. CUSTOMIZE THEFT DETERRENT SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Security

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Mech. Key Entry Alarm Cancel OFF Function That makes it possible to cancel the alarm with an unlock operation using the mechanical key. OFF or ON Main body ECU (multiplex network body ECU)

  5. CUSTOMIZE LIGHTING SYSTEM (INT)


    1. Customizing using the GTS

      Tech Tips

      The following items can be customized.

      Note


      • When the customer requests a change in a function, first make sure that the function can be customized.

      • Be sure to make a note of the current settings before customizing.

      • When troubleshooting a function, first make sure that the function is set to the default setting.


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Illuminated Entry.

      5. Select the setting by referring to the table below.

        Illuminated Entry
        Tester Display Default Content Setting Relevant ECU
        Lighting Time 15 s Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).) 15 s, 7.5 s or 30 s Main body ECU (Multiplex network body ECU)
        I/L when ACC OFF ON Lights up power switch illumination, personal light and room light when the power switch is turned from on (ACC or IG) to off. OFF or ON
        I/L ON W/Door Key Unlock ON Lights up power switch illumination, personal light, room light and footwell lights when doors are unlocked using a mechanical key or door control transmitter. OFF or ON
        Room Light when Aprchd ON Lights up the power switch illumination, personal light and room light when a key enters any actuation area around the doors. OFF or ON
        Inside Foot Light*1 ON ON/OFF of footwell light control function. OFF or ON
        Light Control*1 ON

        Dims (ON setting) or turns off (OFF setting) the footwell lights under the following conditions:


        • Power switch on (READY), shift state other than park (P) has been selected, and all doors closed.

        		 OFF or ON
        Interior Light Control ON Lights up the power switch illumination, front interior light, room light and footwell lights when the illuminated entry function is operating. OFF or ON

        • *1: w/ Footwell Light

    2. Customizing with the Multi-display (for Navigation Receiver Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Light Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Interior Lights Off Timer 15 sec. Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the power switch from off to on (ACC or IG).) Off, 7.5 sec., 15 sec., or 30 sec. Main body ECU (Multiplex network body ECU)

  6. CUSTOMIZE METER / GAUGE SYSTEM


    1. Customizing with the GTS.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Customize Setting / Warning, Display.

    6. Select the setting by referring to the table below.

      Warning
      Tester Display Default Content Setting Relevant ECU
      Key Remind Sound Slow Function to change the cycle of the key reminder buzzer Normal, Fast or Slow Combination meter assembly
      Reverse Buzzer Continual Function to change the type of the reverse warning buzzer Single or Continual Combination meter assembly
      Display
      Tester Display Default Content Setting Relevant ECU
      Tail OFF Indicator ON Function to turn on/off the tail indicator light ON or OFF Combination meter assembly

  7. CUSTOMIZE SEAT BELT WARNING SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.

    • These buzzers should be ON for safe driving. Perform this procedure only if it is necessary to set the buzzer to OFF (disabled).


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Warning.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Driver Side Seatbelt Warning Buzzer ON Function to sound the driver seat belt warning buzzer OFF/ON Combination meter sub-assembly
        Front Passenger Side Seatbelt Warning Buzzer ON Function to sound the front passenger seat belt warning buzzer OFF/ON
        Rear Seatbelt Warning Buzzer ON Function to sound the rear seat belt warning buzzer OFF/ON

        Tech Tips

        This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.

  8. CUSTOMIZE AIR CONDITIONING SYSTEM


    1. Customizing with the GTS

      Tech Tips

      The following items can be customized.

      Note


      • When the customer requests a change in a function, first make sure that the function can be customized.

      • Be sure to make a note of the current settings before customizing.

      • When troubleshooting a function, first make sure that the function is set to the default setting.


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Air Conditioner.

      5. Select the setting by referring to the table below.

        Air Conditioner
        Tester Display Default Content Setting Relevant ECU
        Set Temperature Shift Normal Function to perform control with the shifted temperature versus the displayed temperature -2C, -1C, Normal, +1C, +2C Air conditioning amplifier assembly
        Air Inlet Mode Automatic In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode. Automatic or Manual Air conditioning amplifier assembly
        Foot/DEF Auto Mode ON Function to turn the airflow from FOOT/DEF on automatically when AUTO MODE is on ON or OFF Air conditioning amplifier assembly
        Foot/DEF Automatic Blow Up Function ON Function to increase the blower level automatically when the defroster is on ON or OFF Air conditioning amplifier assembly
        Ambient Temperature Shift Normal Function to display shifted ambient temperature versus actual ambient temperature -3C, -2C, -1C, Normal, +1C, +2C, +3C Air conditioning amplifier assembly
        ECO MODE Cancel OFF Function to cancel the ECO mode drive when item is on OFF or ON Air conditioning amplifier assembly
        Noise and Vibration Reduction OFF Function to change speed of the compressor when item is on OFF or ON Air conditioning amplifier assembly
        Start Pre A/C Long1 Function to set the activation operation method for the remote air conditioning system using the key (electrical transmitter). 1 tim ON, 2 tim ON, Long1 or Long2 Main Body ECU (multiplex network body ECU)
        Stop Pre A/C 2 tim ON Function to set the stop operation method for the remote air conditioning system using the key (electrical transmitter). 1 tim ON, 2 tim ON, Long1 or Long2 Main Body ECU (multiplex network body ECU)

    2. Customizing using the Multi-display (w/ Navigation Receiver Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Climate settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Efficient Ventilation Mode On In case of turning the A/C ON to cool the cabin down quickly, this is the function to change the mode automatically to RECIRCULATION mode On or Off Air conditioning amplifier assembly

  9. CUSTOMIZE POWER WINDOW CONTROL SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function(s) can be customized.

    • Be sure to make notes of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Power Window.

      5. Select the setting by referring to the table below.

        Power Window
        Tester Display Default Content Setting Relevant ECU
        P Window Auto Up Avail This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly (for front passenger door). Not Avl/Avail Power window ECU (Power window regulator motor assembly)
        P Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the front passenger door window using the multiplex network master switch assembly. Not Avl/Avail Power window ECU (Power window regulator motor assembly)
        RR Window Auto Up Avail This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear RH door). Not Avl/Avail Power window ECU (Power window regulator motor assembly)
        RR Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear RH door window using the multiplex network master switch assembly. Not Avl/Avail Power window ECU (Power window regulator motor assembly)
        RL Window Auto Up Avail This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear LH door). Not Avl/Avail Power window ECU (Power window regulator motor assembly)
        RL Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear LH door window using the multiplex network master switch assembly. Not Avl/Avail Power window ECU (Power window regulator motor assembly)

  10. CUSTOMIZE LIGHTING SYSTEM (EXT)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the power switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Light Control.

      5. Select the setting by referring to the table below.

        Light Control
        Tester Display Default Content Setting Relevant ECU
        Response Time*1 Normal Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position. Normal or Long Main Body ECU (Multiplex Network Body ECU)
        Sensitivity Normal Adjusts the sensitivity of the automatic light control sensor.*A Light2, Light1, Normal, Dark1 or Dark2
        Disp Ex ON Sen NORMAL Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*B LIGHT2, LIGHT1, NORMAL, DARK1 or DARK2
        Disp Ex OFF Sen NORMAL Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*C LIGHT2, LIGHT1, NORMAL, DARK1 or DARK2

        • *1: for Australia

        Tech Tips

        The sensitivity adjustment may be difficult to confirm. Check by driving the vehicle.

        *A
        Lighting Brightness A00441B
        Setting Dark2 Dark1 Normal Light1 Light2
        *B
        Brightness of lowering the lights A00441B
        Setting DARK2 DARK1 NORMAL LIGHT1 LIGHT2
        *C
        Brightness when canceling the lowering of the lights A00441B
        Setting DARK2 DARK1 NORMAL LIGHT1 LIGHT2

    2. Customizing with the Multi-display (for Navigation Receiver Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Light settings.

      3. Select the setting by referring to the table below.

        Lights settings
        Display Default Content Setting Relevant ECU
        Light Sensor Sensitivity 0 Adjusts the sensitivity of the automatic light control sensor.*A -2, -1, 0, 1 or 2 Main Body ECU (Multiplex Network Body ECU)

        Tech Tips

        The sensitivity adjustment may be difficult to confirm. Check by driving the vehicle.

        *A
        Lighting Brightness A00441B
        Setting -2 -1 0 1 2

    3. Customizing with the Multi-display (for Radio and Display Type)


      1. Turn the power switch on (IG).

      2. Enter the following menus: SETUP / Vehicle / Vehicle settings.

      3. Select the setting by referring to the table below.

        Vehicle settings
        Display Default Content Setting Relevant ECU
        Light Sensor Sensitivity 0 Adjusts the sensitivity of the automatic light control sensor.*A -2, -1, 0, 1 or 2 Main Body ECU (Multiplex Network Body ECU)

        Tech Tips

        The sensitivity adjustment may be difficult to confirm. Check by driving the vehicle.

        *A
        Lighting Brightness A00441B
        Setting -2 -1 0 1 2