NOISE FILTER INSTALLATION


  1. INSTALL RADIO SETTING CONDENSER


    1. A0043XA

      Engage the claw to install a new terminal cover to the wire harness.

      Note


      • Make sure to hold the wire harness so that the crimping side of the terminal is facing up when installing the wire harness to the terminal cover.

      • Make sure not to bend the exposed wire when installing the wire harness to the terminal cover.

      • Do not use excessive force when inserting the wire harness into the terminal cover.

      • If the terminal cover has been deformed at installation, replace the terminal and terminal cover with new ones.

    2. A0041X6

      Engage the 3 claws to install the terminal cover with wire harness to a new condenser.

      Note


      • Do not use excessive force when inserting the terminal cover into the condenser.

      • If the terminal cover has been deformed at installation, replace the terminal, terminal cover and condenser with new ones.

    3. Engage the clamp to temporarily install the new radio setting condenser with wire harness.

    4. Install the new radio setting condenser with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Connect the connector.

    2. Engage the 7 claws and 2 clips.

    3. Install the deck trim side panel assembly LH with the screw.

  3. INSTALL TONNEAU COVER HOLDER CAP


    1. A00447U

      Engage the claw to install the tonneau cover holder cap.

  4. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY


    1. Engage the 2 guides.

    2. Install the 2 luggage hold belt striker assemblies with the 2 bolts.

  5. INSTALL REAR DECK TRIM COVER


    1. Engage the 4 claws to install the rear deck trim cover.

  6. INSTALL DECK TRIM SERVICE HOLE COVER


    1. Engage the 4 guides.

    2. Engage the 4 claws to install the deck trim service hole cover.

  7. INSTALL REAR NO. 1 FLOOR BOARD


    1. Engage the 3 fasteners.

    2. Install the rear No. 1 floor board with the clip.

    3. Engage each fastener.

  8. INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    1. Engage the claw and 3 clips to install the rear No. 1 floor board sub-assembly.

  9. INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    1. Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.

  10. INSTALL DECK FLOOR BOX LH

    Tech Tips

    Use the same procedure described for the RH side.

  11. INSTALL REAR NO. 4 FLOOR BOARD SUB-ASSEMBLY


    1. Install the rear No. 4 floor board sub-assembly.

  12. INSTALL TONNEAU COVER ASSEMBLY


    1. Install the tonneau cover assembly.

  13. INSTALL DECK FLOOR BOX RH


    1. Engage the claw and 4 guide to install the deck floor box RH.

  14. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  15. INSTALL REAR NO. 2 FLOOR BOARD


    1. Engage the 3 fasteners.

    2. Install the rear No. 2 floor board with the 2 clips.

  16. INSTALL REAR SIDE SEATBACK ASSEMBLY LH


    1. A0040RH

      Engage the 2 guides as shown in the illustration.

    2. Engage the 3 fasteners.

    3. Install the rear side seatback assembly LH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  17. INSTALL REAR SEAT CUSHION ASSEMBLY


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. A0042WJE01
      Text in Illustration
      *1 Rear Hook
      *2 Front Hook

      Engage the 2 rear hooks of the rear seat cushion assembly to the rear seatback assembly.

    3. Engage the 2 front hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

    4. Confirm that the rear seat cushion assembly is firmly installed.

      Note

      When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.

  18. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A00449IE01
      Text in Illustration
      *1 Alignment Mark (Red)

      Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  19. INSTALL REAR DOOR SCUFF PLATE LH


    1. Engage the 7 claws to install the rear door scuff plate LH.