RADIO ANTENNA CORD INSTALLATION


  1. INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. Engage the 4 clamps.

    2. Install the No. 3 antenna cord sub-assembly with the bolt.

    3. Connect the connector.

  2. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

    Tech Tips

    Double-sided tape and tape are not available as supply parts. If the tape still has enough adhesion to secure the roof headlining and antenna cord, reuse it. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedure below.

    If the double-sided tape cannot be reused:


    1. Peel off the release paper from one side of new double-sided tape and apply the new double-sided tape to the position indicated in the illustration. Be careful not to touch the adhesive surface.

      A004459E01
      Text in Illustration
      *1 Double-sided Tape - -
      *a Front *b Double-sided Tape Size
      Double-sided Tape Size
      Area Dimension
      X 1.0 mm (0.0394 in.)
      Y 10.0 mm (0.394 in.)

      Note

      Be sure to apply the double-sided tape carefully so that the tape will not be misaligned or come off.

    2. Peel off the release paper from the double-sided tape. Be careful not to touch the adhesive surface.

    3. Align the vehicle front side marking (pink) on the No. 2 antenna cord sub-assembly with the vehicle front side tab on the roof headlining, and wrap the tape over the antenna cord to install it. (1)

      A0043VGE02
      Text in Illustration
      *1 Tape *2 Extra Cord Storage Area
      *a Front *b Pink

      Tech Tips

      If the tape cannot be reused, packing tape can be used as a substitute.

    4. Temporarily install the front side of the No. 2 antenna cord sub-assembly with the adhesive tape. (2)

    5. Temporarily install the front side of the No. 2 antenna cord sub-assembly with the adhesive tape. (3)

    6. Temporarily install the No. 2 antenna cord sub-assembly by placing it on the double-sided tape from the front of the vehicle to the point just before the extra cord storage area.

    7. Align the vehicle rear marking (pink) on the No. 2 antenna cord sub-assembly with the tape attachment location (scribe line) of the roof headlining, and wrap the tape over the antenna cord to install it. (4)

      Tech Tips

      If the tape cannot be reused, packing tape can be used as a substitute.

    8. Temporarily install the No. 2 antenna cord sub-assembly by placing it on the double-sided tape from the rear of the vehicle to the point just before the extra cord storage area.

    9. A0040SBE01
      Text in Illustration
      *1 Extra Cord Storage Area

      Using tape, place any excess No. 2 antenna cord sub-assembly in the extra cord storage area to finish installing the antenna cord. (5)

  3. INSTALL NO. 3 ROOF SILENCER PAD


    1. Align the markings on the roof headlining assembly with the No. 3 roof silencer pad and install the set plate using hot-melt glue as shown in the illustration.

      A0041TNE01
      Text in Illustration
      *1 Roof Silencer Pad Marking *2 Hot-melt Glue Marking

      Note

      Securely attach the No. 1 roof wire. Failure to do so may cause abnormal noise.

  4. INSTALL NO. 2 ROOF SILENCER PAD


    1. Align the markings on the roof headlining assembly with the No. 2 roof silencer pad and install the set plate using hot-melt glue as shown in the illustration.

      A003ZZCE01
      Text in Illustration
      *1 Roof Silencer Pad Marking *2 Hot-melt Glue Marking

  5. INSTALL ROOF HEADLINING ASSEMBLY

    Click here

  6. INSTALL ANTENNA CORD SUB-ASSEMBLY (for LHD)


    1. for Plug Type Antenna Cord:


      1. Engage the 4 clamps.

      2. Install the antenna cord sub-assembly with the bolt.

      3. Connect the 2 connectors.

    2. for Connector Type Antenna Cord:


      1. Engage the 4 clamps.

      2. Install the antenna cord sub-assembly with the bolt.

      3. Connect the connector.

    3. w/ Digital Audio Broadcasting Antenna:


      1. Engage the 5 clamps.

      2. Install the antenna cord sub-assembly with the bolt.

      3. Connect the 2 connectors.

  7. INSTALL ANTENNA CORD SUB-ASSEMBLY (for RHD)


    1. for Plug Type Antenna Cord:


      1. Engage the 5 clamps.

      2. Install the antenna cord sub-assembly with the bolt.

      3. Connect the 2 connectors.

    2. for Connector Type Antenna Cord:


      1. Engage the 5 clamps.

      2. Install the antenna cord sub-assembly with the bolt.

      3. Connect the connector.

    3. w/ Digital Audio Broadcasting Antenna:


      1. Engage the 6 clamps.

      2. Install the antenna cord sub-assembly with the bolt.

      3. Connect the 2 connectors.

  8. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY

    Click here