PARKING BRAKE CABLE INSTALLATION


  1. INSTALL NO. 2 PARKING BRAKE CABLE CLAMP


    1. for Separate type No. 2 parking brake cable clamp:


      1. A0041OO

        Disengage the 2 claws to remove the No. 2 parking brake cable clamp from the No. 3 parking brake cable assembly.

    2. for One-piece type No. 2 parking brake cable clamp:


      1. Using pliers or equivalent, disconnect the No. 2 parking brake cable clamp and remove it from the No. 3 parking brake cable assembly.

        Tech Tips

        No. 2 parking brake cable clamp cannot be reused once removed. Make sure to remove it from the No. 3 parking brake cable clamp.

  2. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. Install the No. 3 parking brake cable assembly with the 5 bolts.

      A0041SY
      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }
    2. A00424NE04
      Text in Illustration
      *1 No. 3 Parking Brake Cable Assembly
      *2 Clip

      Install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

      Tech Tips

      Be sure to engage the No. 3 parking brake cable assembly clip onto the rear disc brake cylinder assembly as shown in the illustration.

    3. A0041YXE02

      Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

    4. A003ZXE

      Engage the clamp to install the No. 2 parking brake cable clamp.

  3. INSTALL REAR FLOOR SIDE MEMBER COVER LH


    1. Install the rear floor side member cover LH with the nut and 2 bolts.

  4. INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR


    1. A0040HZ

      Install the front No. 2 floor heat insulator with the 3 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  5. INSTALL FRONT EXHAUST PIPE ASSEMBLY

    Click here

  6. INSTALL NO. 1 PARKING BRAKE PULL ROD SUB-ASSEMBLY


    1. A0043DV

      Connect the No. 3 parking brake cable assembly to the No. 1 parking brake pull rod sub-assembly as shown in the illustration.

    2. Connect the No. 2 parking brake cable assembly to the No. 1 parking brake pull rod sub-assembly.

      Tech Tips

      Perform the same procedure as for the No. 3 parking brake cable assembly.

  7. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD)


    1. Pass the No. 1 parking brake cable assembly through the parking brake pedal assembly.

    2. A0043N6

      Install the clip to the No. 1 parking brake cable assembly.

    3. A0042FX

      Bend the parking brake pedal claw.

    4. A0040ZH

      Temporarily install the adjusting nut.

  8. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY (for RHD)


    1. Pass the No. 1 parking brake cable assembly through the parking brake pedal assembly.

    2. A00449H

      Install the clip to the No. 1 parking brake cable assembly.

    3. A004057

      Bend the parking brake pedal claw.

    4. A004449

      Temporarily install the adjusting nut.

  9. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY (for LHD)

    Click here

  10. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY (for RHD)

    Click here

  11. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }