PARKING BRAKE PEDAL (for LHD) INSTALLATION


  1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. A0042F1

      Install the parking brake control pedal assembly with the bolt and 2 nuts.

      Torque:
      15 N*m  { 148 kgf*cm, 11 ft.*lbf }
    2. A00424I

      Connect the parking brake switch connector.

    3. Engage the wire harness clamp.

    4. A0042BW

      Install the No. 1 parking brake cable assembly with the 5 bolts and nut.

      Torque:
      15 N*m  { 148 kgf*cm, 11 ft.*lbf }

    5. Engage the clamp.

    6. A0040IAE02
      Text in Illustration
      *1 Lock Nut

      Temporarily install the lock nut.

      Tech Tips

      After adjusting parking brake pedal travel, tighten the lock nut.

  2. CONNECT NO. 1 PARKING BRAKE PULL ROD SUB-ASSEMBLY


    1. A004269E01
      Text in Illustration
      *1 Turn
      *2 Hold

      Connect the No. 1 parking brake pull rod sub-assembly to the parking brake control pedal assembly as shown in the illustration.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  3. INSTALL NO. 3 BELT ANCHOR REINFORCEMENT SUB-ASSEMBLY


    1. A0041H3

      Install the No. 3 belt anchor reinforcement sub-assembly with the 4 bolts.

      Torque:
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }

  4. INSTALL NO. 2 BELT ANCHOR REINFORCEMENT SUB-ASSEMBLY


    1. A004464

      Install the No. 2 belt anchor reinforcement sub-assembly with the 4 bolts.

      Torque:
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }

  5. INSTALL FRONT SEAT ASSEMBLY LH

    Click here

  6. INSTALL FRONT SEAT ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  7. INSTALL AIR CONDITIONING UNIT

    Click here

  8. ADJUST PARKING BRAKE PEDAL TRAVEL


    1. Remove the front door scuff plate LH Click here.

    2. Remove the cowl side trim board LH Click here.

    3. Remove the lower instrument panel finish panel assembly Click here.

    4. Completely release the parking brake pedal.

    5. A0040PUE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Loosen the lock nut and the adjusting nut to completely release the parking brake cable.

    6. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

      Parking brake pedal travel
      8 to 11 notches at 300 N (31 kgf, 67.5 lbf)
    7. A0040PUE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    8. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

    9. Check whether the parking brake drags or not.

    10. Install the lower instrument panel finish panel assembly Click here.

    11. install the cowl side trim board LH Click here.

    12. install the front door scuff plate LH Click here.

  9. INSPECT BRAKE WARNING LIGHT


    1. When operating the parking brake pedal, check that the brake warning light illuminates.

      Standard
      The brake warning light always illuminates at the first click.