REAR SPEED SENSOR INSTALLATION

Tech Tips


  • The rear speed sensor is a component of the rear axle hub and bearing assembly. If the sensor malfunctions, replace the rear axle hub and bearing assembly.

  • If the sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.


  1. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY


    1. Install the rear axle hub and bearing assembly Click here.

      Tech Tips

      The rear speed sensor is a component of the rear axle hub and bearing assembly. If the sensor malfunctions, replace the rear axle hub and bearing assembly.

  2. INSPECT REAR AXLE HUB BEARING LOOSENESS


    1. A0040S5

      Using a dial indicator, check for looseness near the center of the axle hub.

      Maximum looseness
      0.05 mm (0.00196 in.)

      Note


      • Ensure that the dial indicator is set perpendicular to the measurement surface.

      • Keep the magnet of the dial indicator away from the rear axle hub and bearing (rear speed sensor).

      Tech Tips

      If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.

  3. INSPECT REAR AXLE HUB RUNOUT


    1. A003ZZP

      Using a dial indicator, check for runout on the surface of the axle hub outside the rear axle hub bolt.

      Maximum runout
      0.05 mm (0.00196 in.)

      Note


      • Ensure that the dial indicator is set perpendicular to the measurement surface.

      • Make sure to install the tip of the dial indicator towards the outside of the rear axle hub bolt.

      • Keep the magnet of the dial indicator away from the rear axle hub and bearing (rear speed sensor).

      Tech Tips

      If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.

  4. INSTALL REAR DISC


    1. A0043NIE06
      Text in Illustration
      *a Matchmark

      Align the matchmarks of the disc and axle hub, and install the disc.

      Note

      When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.

  5. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


    1. Install the rear disc brake caliper assembly with the 2 bolts.

      Torque:
      57 N*m  { 585 kgf*cm, 42 ft.*lbf }

  6. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A00424NE03
      Text in Illustration
      *1 No. 3 Parking Brake Cable Assembly
      *2 Clip

      Install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

      Tech Tips

      Be sure to engage the No. 3 parking brake cable assembly clip onto the rear disc brake cylinder assembly as shown in the illustration.

    2. A0041YXE02

      Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

  7. CONNECT SKID CONTROL SENSOR WIRE


    1. Connect the skid control sensor wire connector to the rear speed sensor.

  8. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


    1. Connect the cable to the negative (-) auxiliary battery terminal Click here.

    2. Connect the reservoir level switch connector.

    3. Clear the DTCs Click here.

  9. ADJUST PARKING BRAKE

    Click here

  10. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)


    1. Connect each connector.

    2. Engage the clamp.

    3. Engage the 2 guides and claw to connect the hood lock control cable.

    4. A00412T

      Engage the 6 claws and clip.

    5. Install the lower instrument panel finish panel assembly with the screw <C>.

  11. INSTALL COWL SIDE TRIM BOARD LH (for LHD)


    1. Engage the 2 clips.

    2. Install the cowl side trim board LH with the clip.

  12. INSTALL FRONT DOOR SCUFF PLATE LH (for LHD)


    1. Engage the 10 claws to install the front door scuff plate LH.

  13. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Connect each connector.

    2. Engage the guide and 2 claws.

    3. Install the No. 1 instrument panel under cover sub-assembly with the screw <D>.

  14. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  15. CHECK FOR SPEED SENSOR SIGNAL

    Click here