DYNAMIC RADAR CRUISE CONTROL SYSTEM, Diagnostic DTC:C1A50

DTC Code DTC Name
C1A50 Brake System

DESCRIPTION

When the driving support ECU assembly receives an electronically controlled brake system malfunction signal from the brake booster with master cylinder assembly (skid control ECU) via CAN communication, DTC C1A50 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A50 While power switch is on (IG), signal malfunction from brake booster with master cylinder assembly (skid control ECU) continues for 1 second while dynamic radar cruise control is operating

  • Electronically controlled brake system

  • Driving support ECU assembly

WIRING DIAGRAM

A0042VUE04

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.

    5. Check for DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

    B

    GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM Click here

    A

  2. CHECK FOR DTCs (DTC C1A50)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs Click here.

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed for which radar cruise control operation is possible.

      2. Turn the cruise control system on using the cruise control switch (ON-OFF button).

      3. Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.

    5. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.

    6. Check for DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A50 is output B

    B

    REPLACE DRIVING SUPPORT ECU ASSEMBLY Click here

    A

    USE SIMULATION METHOD TO CHECK Click here

  3. REPLACE DRIVING SUPPORT ECU ASSEMBLY


    1. Replace the driving support ECU assembly Click here.


    NEXT

  4. CHECK FOR DTCs (DTC C1A50)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs Click here.

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed for which radar cruise control operation is possible.

      2. Turn the cruise control system on using the cruise control switch (ON-OFF button).

      3. Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.

    5. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.

    6. Check for DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A50 is output B

    B

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY Click here

    A

    END

  5. REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY


    1. Replace the brake booster with master cylinder assembly (skid control ECU) Click here (for LHD), Click here (for RHD)).


    NEXT

  6. CHECK FOR DTCs (DTC C1A50)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Clear the DTCs Click here.

    4. Perform the following to make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the malfunction cannot be detected.


      1. Drive the vehicle at a speed for which radar cruise control operation is possible.

      2. Turn the cruise control system on using the cruise control switch (ON-OFF button).

      3. Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.

    5. Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.

    6. Check for DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC C1A50 is output B

    B

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    A

    END