FRONT DOOR GLASS WEATHERSTRIP REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL


    1. A01J46B

      Using a moulding remover, detach the 2 clips and 4 claws.

    2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

  4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    1. A01J5X9

      Detach the 2 clips and remove the front door lower frame bracket garnish.

  5. REMOVE DOOR PULL HANDLE


    1. A01J3V5

      Remove the screw and door pull handle.

  6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01J6S3E01
      Text in Illustration
      *1 Clip
      *2 Screw

      Remove the clip and screw.

    2. Detach the 8 clips and remove the front door trim board.

  7. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

    A01J6DA

    1. w/ Power Mirror Control System:

      Disconnect the mirror connector.

    2. Remove the 3 nuts.

    3. Push down the claw and remove the outer rear view mirror assembly LH.

  8. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. A01J4S0E01

      Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.

    2. A01J53B

      Disconnect the front door inside locking cable and front door lock remote control cable and remove the front door inside handle.

  9. REMOVE FRONT DOOR NO. 1 TRIM BRACKET


    1. A01J47S

      Remove the 2 screws and front door No. 1 trim bracket.

  10. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A01J4P2

      Pull out the front door inside locking cable, front door lock remote control cable and wire harness from the front door service hole cover, and then remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the front door panel.

  11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Temporarily install the power window regulator master switch assembly with front door armrest base panel.

    2. Connect the cable to the negative (-) battery terminal.

    3. Move the front door glass sub-assembly so that the front door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. Remove the power window regulator master switch assembly with front door armrest base panel.

    6. A01J797

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the front door glass to fall.

    7. A01J3KME01

      Remove the front door glass as indicated by the arrows in the order shown in the illustration.

      Note

      Do not damage the front door glass.

  12. REMOVE FRONT DOOR OUTER GLASS WEATHERSTRIP ASSEMBLY LH


    1. A01J53DE01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front door outer glass weatherstrip.

    2. Detach the 5 claws and remove the front door outer glass weatherstrip.