FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining) INSTALLATION


  1. INSTALL FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining)


    1. A01J7IV

      Temporarily install the power seat motor with the 3 bolts.

    2. A01J5AL

      Install the reclining rod.

    3. A01J76X

      Attach the 6 claws to install the push nut to the reclining rod.

    4. Using a 4 mm socket hexagon wrench, tighten the 3 bolts.

      Torque:
      4.5 N*m  { 46 kgf*cm, 40 in.*lbf }
    5. A01J5R6

      Attach the 8 hooks to install the seatback spring.

    6. Connect the connector.

  2. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH


    1. A01J3QFE02

      Attach the guide to install the reclining adjuster inside cover.

    2. Install the screw.

  3. INSTALL LOWER RECLINING ADJUSTER INSIDE COVER LH


    1. A01J3K4

      Attach the claw to install the reclining adjuster inside cover.

    2. Install the screw.

  4. INSTALL NO. 1 SEATBACK CLOTH


    1. A01J4A2

      Install the seatback cloth.

  5. INSTALL SEPARATE TYPE FRONT SEATBACK PAD


    1. A01J6N4

      Install the seatback pad.

  6. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A01J5KE

      Using hog ring pliers, attach the strap of the seatback cover to the seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A01J7BU

      Attach the 4 claws to install the 2 headrest supports.

    3. A01J7NC

      Using hog ring pliers, install the upper part of the seatback cover to the seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    4. A01J4DR

      Using hog ring pliers, install the center of the seatback cover to the seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    5. A01J5JW

      Using hog ring pliers, attach the strap of the seatback cover to the seatback frame with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    6. A01J5GV

      Using hog ring pliers, attach the bottom of the seatback cloth to the seatback frame with new hog rings.

    7. A01J6KM

      Using hog ring pliers, attach the wires at the bottom of the seatback cover with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  7. INSTALL FRONT SEAT CUSHION INNER SHIELD LH


    1. Pass the wire harness of the front seat inner belt assembly below the claw and into the front seat cushion inner shield.

      A01J5M8
    2. A01J6UR

      Attach the claw to temporarily install the cushion inner shield.

      Note

      Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat cushion inner shield.

    3. A01J34Y

      Attach the guide and claw.

      Note

      Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat cushion inner shield.

    4. Install the screw to the cushion inner shield.

  8. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT INNER NO. 1 SEAT CUSHION SHIELD


    1. A01J3WV

      Attach the claw and guide to install the cushion shield.

    2. Install the 3 screws.

    3. A01J4HV

      Install the 2 screws.

  9. INSTALL SLIDE & VERTICAL POWER SEAT SWITCH KNOB


    1. A01J7MZ

      Attach the 4 claws to install the knob.

  10. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A01J7F6

      Attach the 2 claws to install the knob.

  11. INSTALL FRONT SEAT ASSEMBLY


    1. Install the front seat assembly Click here.

  12. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.

  13. INSPECT FRONT SEAT ASSEMBLY


    1. Check the power seat operation Click here.