REAR NO. 1 SEAT ASSEMBLY (for RH Side) DISASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


  1. REMOVE REAR SEAT HEADREST ASSEMBLY


    1. Remove the rear seat headrest assembly.

  2. REMOVE REAR NO. 1 SEAT RECLINING COVER LH


    1. A01J5T4E01
      Text in Illustration
      *1 Guide A
      *2 Guide B
      A01J5O1 Pull
      A01J67K Pull Up

      Remove the screw.

    2. Pull the rear No. 1 seat reclining cover LH to detach the claw and guide B.

    3. Pull up the rear No. 1 seat reclining cover LH to detach the guide A and remove the rear No. 1 seat reclining cover LH.

  3. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH


    1. A01J523

      Remove the screw and reclining adjuster release handle RH.

  4. REMOVE REAR NO. 1 SEAT RECLINING COVER RH


    1. A01J4ZT

      Remove the screw.

    2. Pull the rear No. 1 seat reclining cover RH to detach the 3 claws.

      Text in Illustration
      A01J5O1 Pull
      A01J67K Pull Up

    3. Pull up the rear No. 1 seat reclining cover RH to detach the guide and remove the rear No. 1 seat reclining cover RH.

  5. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH

    A01J3SIE01

    1. Remove the bolt and seat belt.

  6. REMOVE REAR NO. 1 SEATBACK ASSEMBLY


    1. A01J46T

      Remove the 4 bolts and rear No. 1 seatback assembly.

  7. REMOVE REAR NO. 1 SEATBACK COVER


    1. Detach the 2 pieces of fastening tape and the hook.

      A01J5A9E01
      Text in Illustration
      *1 Fastening Tape *2 Hook
      *3 Fastener - -

    2. Open the fastener and roll up the rear No. 1 seatback cover.

    3. A01J4L3

      Remove the rear seatback board RH.

    4. A01J371

      Remove the 2 nuts and hog rings.

    5. A01J3S9

      Slightly pull out the rear seat armrest assembly RH, pull the rear No. 1 seatback cover out from the rear of the rear seat armrest, and then remove the rear seat armrest assembly RH.

    6. Roll up the rear No. 1 seatback cover and detach the 2 hooks.

      A01J7MW
    7. A01J52B

      Detach the 4 claws and remove the 2 rear seat headrest supports.

    8. A01J6X2

      Remove the hog rings and rear No. 1 seatback cover from the rear No. 1 seatback pad RH.

  8. REMOVE REAR NO. 1 SEATBACK PAD RH

    Note

    As the rear No. 1 seatback pad RH is affixed to the rear No. 1 seatback frame, do not remove the rear No. 1 seatback pad RH from the rear No. 1 seatback frame unless it is necessary to replace the rear No. 1 seatback pad RH. If the rear No. 1 seatback pad RH is removed from the rear No. 1 seatback frame, make sure to replace the rear No. 1 seatback pad RH.


    1. A01J61J

      Remove the rear No. 1 seatback pad RH from the rear No. 1 seatback frame.

    2. If reusing the rear No. 1 seatback frame:

      Remove any remaining pad and adhesive from the rear No. 1 seatback frame.

  9. REMOVE REAR SEAT ARMREST ARM LH


    1. A01J70C

      Remove the bolt and rear seat armrest arm LH.

  10. REMOVE REAR SEAT ARMREST BUSH LH


    1. A01J3OJ

      Remove the rear seat armrest bush LH from the rear seat armrest arm LH.

  11. REMOVE REAR SEAT ARMREST ARM RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE REAR SEAT ARMREST BUSH RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. REMOVE RECLINING REMOTE CONTROL LEVER KNOB RH


    1. A01J3YG

      Remove the screw and reclining remote control lever knob RH from the rear seat lock assembly RH.

  14. REMOVE REAR NO. 1 SEAT LOCK COVER RH

    A01J31D

    1. Remove the 7 screws and rear No. 1 seat lock cover RH.

    2. A01J5JC

      Detach the cable clamp and disconnect the rear seat lock control cable RH.

  15. REMOVE REAR NO. 2 SEAT LOCK COVER RH


    1. A01J6GA

      Remove the 2 screws and rear No. 2 seat lock cover RH from the rear seat lock assembly LH.

  16. REMOVE REAR SEAT HINGE ASSEMBLY LH


    1. A01J5GN

      Remove the 2 nuts and rear seat hinge assembly LH from the inner seat track assembly RH.

  17. REMOVE REAR SEAT HINGE ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. REMOVE REAR SEATBACK LOCK RELEASE BUTTON


    1. A01J7GXE01
      Text in Illustration
      *1 Protective Tape
      *2 Reclining Release Handle Sub-assembly

      Using 2 clip removers, remove the 2 rear seatback lock release buttons from the reclining release handle sub-assembly.

      Tech Tips


      • Tape the clip remover tips before use.

      • If a rear seatback lock release button is damaged, replace it with a new one.

  19. REMOVE RECLINING RELEASE HANDLE SUB-ASSEMBLY

    A01J4QG

    1. Disconnect the reclining release handle sub-assembly from the rear seat lock assembly RH as shown in the illustration.

    2. Pull the reclining release handle sub-assembly and through the hole of the rear seat cushion under cover sub-assembly RH.

  20. REMOVE REAR SEAT LOCK ASSEMBLY LH

    A01J3H8E01

    1. Detach the cable clamp.

    2. Twist the cable end in the direction indicated by the arrow and disconnect the rear seat lock control cable RH.

      Text in Illustration
      *1 Cable End
    3. A01J3PM

      Using needle nose pliers, remove the rear seat cushion support spring LH.

    4. A01J6M6

      Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts, washer and rear seat lock assembly LH from the rear No. 1 seat track bracket.

  21. REMOVE REAR NO. 1 SEAT TRACK BRACKET


    1. A01J42K

      Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts and rear No. 1 seat track bracket from the inner seat track assembly RH.

  22. REMOVE REAR SEAT CUSHION SUPPORT SPRING RH


    1. A01J6R0

      Using needle nose pliers, remove the rear seat cushion support spring RH.

  23. REMOVE REAR SEAT LOCK ASSEMBLY RH

    A01J52Q

    1. Detach the cable clamp and disconnect the rear seat lock control cable RH from the outer seat track assembly RH.

    2. Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts and rear seat lock assembly RH from the outer seat track assembly RH.

    3. A01J6DN

      Remove the E-ring and washer.

    4. A01J78Q

      Disconnect the rear seat lock control cable RH from the rear seat lock assembly RH.

    5. A01J37C

      Remove the washer.

  24. REMOVE SEAT TRACK ADJUSTING HANDLE

    Tech Tips

    Perform this procedure when removing and reinstalling or replacing only the seat track adjusting handle.


    1. Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the position shown in the illustration.

      A01J3AZE01
      Text in Illustration
      *1 Seat Track Adjusting Handle Lock *2 Inner Seat Track Assembly RH
      *3 Outer Seat Track Assembly RH *4 Seat Track Adjusting Handle

    2. Insert a screwdriver into the outer seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.

      Note

      Do not use excessive force to pull out the seat track adjusting handle.

      A01J6LXE01
      Text in Illustration
      *1 Screwdriver *2 Outer Seat Track Assembly RH
      *3 Seat Track Adjusting Handle Lock *4 Seat Track Adjusting Handle

    3. Insert a screwdriver into the inner seat track assembly LH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.

      Note

      Do not use excessive force to pull out the seat track adjusting handle.

      A01J6Z8E01
      Text in Illustration
      *1 Screwdriver *2 Inner Seat Track Assembly RH
      *3 Seat Track Adjusting Handle Lock *4 Seat Track Adjusting Handle
    4. A01J5K6

      Pull and remove the seat track adjusting handle from the outer seat track assembly RH and inner seat track assembly RH.

  25. REMOVE REAR SEAT TRACK ASSEMBLY RH


    1. A01J7JA

      Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the foremost position.

    2. Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts.

    3. Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the position shown in the illustration.

      A01J45TE01
      Text in Illustration
      *1 Seat Track Adjusting Handle Lock *2 Inner Seat Track Assembly RH
      *3 Outer Seat Track Assembly RH *4 Seat Track Adjusting Handle

    4. Insert a screwdriver into the outer seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.

      Note

      Do not use excessive force to pull out the seat track adjusting handle.

      A01J4UZE01
      Text in Illustration
      *1 Screwdriver *2 Outer Seat Track Assembly RH
      *3 Seat Track Adjusting Handle Lock *4 Seat Track Adjusting Handle

    5. Insert a screwdriver into the inner seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.

      Note

      Do not use excessive force to pull out the seat track adjusting handle.

      A01J34TE01
      Text in Illustration
      *1 Screwdriver *2 Inner Seat Track Assembly RH
      *3 Seat Track Adjusting Handle Lock *4 Seat Track Adjusting Handle
    6. A01J693

      Pull and remove the seat track adjusting handle from the outer seat track assembly RH and inner seat track assembly RH.

    7. A01J6CZ

      Using a T40 "TORX" socket wrench, remove the "TORX" bolt and outer seat track assembly RH.

    8. A01J6IJ

      Using a T40 "TORX" socket wrench, remove the "TORX" bolt and inner seat track assembly RH.

  26. REMOVE REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY RH


    1. A01J5VC

      Detach the hooks.

    2. A01J3YK

      Remove the 4 screws.

    3. Detach the 2 guides and remove the rear seat cushion under cover sub-assembly RH.

  27. REMOVE REAR NO. 1 SEAT CUSHION COVER

    A01J31ZE01
    Text in Illustration
    *1 No. 1 Fold Seat Stopper Band Assembly

    1. Pull out the No. 1 fold seat stopper band assembly.

    2. Remove the hog rings and rear No. 1 seat cushion cover from the rear No. 1 seat cushion pad.

    3. Pass the rear center seat lap type belt assembly and rear seat lap type belt assembly RH through the hole of the rear No. 1 seat cushion cover.

  28. REMOVE REAR NO. 1 SEAT CUSHION PAD RH

    A01J5SY

    1. Pass the rear center seat lap type belt assembly and rear seat lap type belt assembly RH through the hole of the rear No. 1 seat cushion pad.

    2. Remove the rear No. 1 seat cushion pad RH from the rear No. 1 seat cushion frame sub-assembly.

  29. REMOVE REAR CENTER SEAT LAP TYPE BELT ASSEMBLY

    A01J4XJE01

    1. Remove the bolt and seat belt center.

  30. REMOVE REAR SEAT LAP TYPE BELT ASSEMBLY LH

    A01J4X0E01

    1. Remove the bolt and seat belt LH.

  31. REMOVE NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY

    A01J78T

    1. Untie the No. 1 fold seat stopper band assembly from the rear No. 1 seat cushion frame sub-assembly as shown in the illustration and remove the No. 1 fold seat stopper band assembly.