POWER WINDOW CONTROL SYSTEM (w/ Jam Protection Function) Remote Up / Down Function does not Operate

DESCRIPTION

With the ignition switch ON, the power window regulator master switch assembly transmits remote switch signals to the power window regulator switches of the front passenger side power window and rear power windows. Then, each power window regulator switch drives its respective power window regulator motor.

WIRING DIAGRAM

A01J5J3E12

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    1. Turn the window lock switch off and operate the switches on the power window regulator master switch assembly. Check that the remote up/down function operates normally.

      OK
      Remote up/down function operates normally.

    NG

    CHECK MANUAL UP/DOWN FUNCTION Click here

    OK

    END

  2. CHECK MANUAL UP/DOWN FUNCTION


    1. Check that the front passenger side power window and rear power window manual up/down function operates normally.

      OK
      Manual up/down function operates normally.

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH)


    1. Disconnect the P6 power window regulator master switch assembly connector.

    2. Disconnect the P11 front power window regulator switch assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P6-13 (U) - P11-1 Always Below 1 Ω
      P6-15 (D) - P11-4 Always Below 1 Ω
      P6-13 (U) or P11-1 - Body ground Always 10 kΩ or higher
      P6-15 (D) or P11-4 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)


    1. Disconnect the P6 power window regulator master switch assembly connector.

    2. Disconnect the P12 rear power window regulator switch assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P6-12 (U) - P12-1 Always Below 1 Ω
      P6-10 (D) - P12-4 Always Below 1 Ω
      P6-12 (U) or P12-1 - Body ground Always 10 kΩ or higher
      P6-10 (D) or P12-4 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH)


    1. Disconnect the P6 power window regulator master switch assembly connector.

    2. Disconnect the P13 rear power window regulator switch assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P6-18 (U) - P13-1 Always Below 1 Ω
      P6-16 (D) - P13-4 Always Below 1 Ω
      P6-18 (U) or P13-1 - Body ground Always 10 kΩ or higher
      P6-16 (D) or P13-4 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here