REAR SEAT OUTER BELT ASSEMBLY INSTALLATION

Tech Tips


  • Use the same procedures for the LH side and RH side.

  • The procedure listed below are for the RH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL REAR NO. 2 SEAT BELT ASSEMBLY OUTER RH

    A01J6U7E01

    1. Align the claws with the seat belt positioning holes and install the retractor of the seat belt with the bolt as shown in the illustration.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. A01J5QLE05

      Connect the shoulder anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. Close the cover cap.

  2. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY OUTER RH

    A01J3AAE01

    1. Align the claws with the seat belt positioning holes and install the retractor of the seat belt with the bolt as shown in the illustration.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. A01J5QLE05

      Connect the shoulder anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. Close the cover cap.

  3. INSTALL QUARTER INSIDE TRIM BOARD RH


    1. Detach the 8 claws and 10 clips to install the quarter inside trim board.

    2. Install the clip.

    3. Connect the rear No. 2 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    4. Connect the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    5. Attach the 2 claws to install the outer lap belt anchor cover.

      Tech Tips

      Use the same procedure for both outer lap belt anchor covers.

  4. CONNECT REAR NO. 2 SEAT BELT ASSEMBLY OUTER RH

    A01J3XYE01

    1. Connect the seat belt's floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. A01J5NGE04

      Install the belt outer anchor cover.

  5. CONNECT REAR NO. 1 SEAT BELT ASSEMBLY OUTER RH

    A01J62JE01

    1. Connect the seat belt's floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. A01J5NGE01

      Install the belt outer anchor cover.

  6. INSTALL QUARTER TRIM HOOK

    Tech Tips

    Use the same procedure for both quarter trim hooks.


    1. Install the quarter trim hook with the screw.

  7. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL BACK DOOR SCUFF PLATE


    1. Attach the 4 claws, 2 guides and 6 clips to install the back door scuff plate.

  10. INSTALL REAR NO. 2 SEAT ASSEMBLY RH


    1. Fully tilt the seatback forward.

    2. A01J6NKE01

      Place the seat onto the lock striker.

      Note

      Be careful not to damage the vehicle body.

    3. Tighten the bolt on the rear side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

    4. Tighten the bolt on the front side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

    5. Fully lock the seat to the lock striker.

      Tech Tips

      Confirm that the seat is firmly locked to the lock striker.