OUTER REAR VIEW MIRROR INSPECTION

PROCEDURE

1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Automatic Retractable Mirror)

   
   

   1. Check the operation of the mirror surface.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Apply battery voltage and check the operation of the outer rear view mirror assembly LH.

         OK

         Measurement Condition Specified Condition Battery positive (+) → Terminal 1 (MV) Battery negative (-) → Terminal 2 (M+) Turns upward Battery positive (+) → Terminal 2 (M+) Battery negative (-) → Terminal 1 (MV) Turns downward Battery positive (+) → Terminal 3 (MH) Battery negative (-) → Terminal 2 (M+) Turns left Battery positive (+) → Terminal 2 (M+) Battery negative (-) → Terminal 3 (MH) Turns right

         If the result is not as specified, replace the outer rear view mirror assembly LH.

   2. Check the operation of the mirror heater. (w/ Mirror Heater)

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 6 (+) - 7 (-) 25°C (75°F) 8 to 11 Ω

         If the result is not as specified, replace the outer rear view mirror assembly LH.

2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Automatic Retractable Mirror)

   
   

   1. Check the operation of the mirror surface.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Apply battery voltage and check the operation of the outer rear view mirror assembly LH.

         OK

         Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (MV) Battery negative (-) → Terminal 5 (M+) Turns upward Battery positive (+) → Terminal 5 (M+) Battery negative (-) → Terminal 6 (MV) Turns downward Battery positive (+) → Terminal 4 (MH) Battery negative (-) → Terminal 5 (M+) Turns left Battery positive (+) → Terminal 5 (M+) Battery negative (-) → Terminal 4 (MH) Turns right

         If the result is not as specified, replace the outer rear view mirror assembly LH.

   2. Check the operation of the retractable mirror.

      Note

      
      

      • Disconnect and reconnect the battery between each mirror position check.

      • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

         OK

         Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Forward position A Moves from A to retracted position E Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Forward position A Does not move Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Position B Moves from B to retracted position E Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Position B Does not move Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Driving position C Moves from C to retracted position E Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Driving position C Does not move Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Position D Moves from D to retracted position E Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Position D Moves from D to driving position C Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Retracted position E Does not move Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Retracted position E Moves from E to driving position C

         If the result is not as specified, replace the outer rear view mirror assembly LH.

   3. Check the operation of the mirror heater.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 7 (+) - 8 (-) 25°C (75°F) 8 to 11 Ω

         If the result is not as specified, replace the outer rear view mirror assembly LH.

3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Automatic Retractable Mirror)

   
   

   1. Check the operation of the mirror surface.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Apply battery voltage and check the operation of the outer rear view mirror assembly RH.

         OK

         Measurement Condition Specified Condition Battery positive (+) → Terminal 1 (MV) Battery negative (-) → Terminal 2 (M+) Turns upward Battery positive (+) → Terminal 2 (M+) Battery negative (-) → Terminal 1 (MV) Turns downward Battery positive (+) → Terminal 3 (MH) Battery negative (-) → Terminal 2 (M+) Turns left Battery positive (+) → Terminal 2 (M+) Battery negative (-) → Terminal 3 (MH) Turns right

         If the result is not as specified, replace the outer rear view mirror assembly RH.

   2. Check the operation of the mirror heater. (w/ Mirror Heater)

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 6 (+) - 7 (-) 25°C (75°F) 8 to 11 Ω

         If the result is not as specified, replace the outer rear view mirror assembly RH.

4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Automatic Retractable Mirror)

   
   

   1. Check the operation of the mirror surface.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Apply battery voltage and check the operation of the outer rear view mirror assembly RH.

         OK

         Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (MV) Battery negative (-) → Terminal 5 (M+) Turns upward Battery positive (+) → Terminal 5 (M+) Battery negative (-) → Terminal 6 (MV) Turns downward Battery positive (+) → Terminal 4 (MH) Battery negative (-) → Terminal 5 (M+) Turns left Battery positive (+) → Terminal 5 (M+) Battery negative (-) → Terminal 4 (MH) Turns right

         If the result is not as specified, replace the outer rear view mirror assembly RH.

   2. Check the operation of the retractable mirror.

      Note

      
      

      • Disconnect and reconnect the battery between each mirror position check.

      • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

         OK

         Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Forward position A Moves from A to retracted position E Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Forward position A Does not move Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Position B Moves from B to retracted position E Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Position B Does not move Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Driving position C Moves from C to retracted position E Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Driving position C Does not move Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Position D Moves from D to retracted position E Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Position D Moves from D to driving position C Battery positive (+) → Terminal 11 (MR) Battery negative (-) → Terminal 10 (MF) Retracted position E Does not move Battery positive (+) → Terminal 10 (MF) Battery negative (-) → Terminal 11 (MR) Retracted position E Moves from E to driving position C

         If the result is not as specified, replace the outer rear view mirror assembly RH.

   3. Check the operation of the mirror heater.

      
      
      1. 

         Text in Illustration

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 7 (+) - 8 (-) 25°C (75°F) 8 to 11 Ω

         If the result is not as specified, replace the outer rear view mirror assembly RH.