WINDOW DEFOGGER SYSTEM Rear Window Defogger System does not Operate

DESCRIPTION

When the rear window defogger switch is turned on, a rear window defogger activation request signal is transmitted from the air conditioning control assembly to the air conditioning amplifier assembly. Upon receipt of the signal, the air conditioning amplifier assembly turns on the DEF relay to activate the rear window defogger system.

WIRING DIAGRAM

A01V02GE01

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

    5. According to the display on the GTS, perform the Active Test.

      Air Conditioner
      Tester Display Test Part Control Range Diagnostic Note
      Defogger Relay (Rear) DEF relay OFF or ON -
      OK
      The window defogger system operates normally.

    OK
    NG
  2. INSPECT DEF RELAY


    1. Inspect the DEF relay Click here.


    NG
    OK
  3. CHECK HARNESS AND CONNECTOR (DEF RELAY - IG1 NO. 1 RELAY, AUXILIARY BATTERY AND BODY GROUND)


    1. A01V1JME01
      Text in Illustration
      *1 No. 2 Engine Room Relay Block
      *2 DEF Relay Holder

      Remove the DEF relay from the No. 2 engine room relay block.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      1 - Body ground Ignition switch ON (IG) 11 to 14 V
      5 - Body ground Always 11 to 14 V
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4 - Body ground Always Below 1 Ω

    NG
    OK
  4. CHECK HARNESS AND CONNECTOR (DEF RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. Remove the DEF relay from the No. 2 engine room relay block.

    2. Disconnect the F29 air conditioning amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Relay terminal 2 - F29-38 (RDFG) Always Below 1 Ω
      Relay terminal 2 - Body ground Always 10 kΩ or higher

    NG
    OK
  5. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


    1. Reconnect the F29 air conditioning amplifier assembly connector.

    2. Reinstall the DEF relay.

    3. A01V0VPE02
      Text in Illustration
      *a

      Component with harness connected

      (Air Conditioning Amplifier Assembly)

      Remove the air conditioning amplifier assembly with its connectors still connected Click here.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      F29-38 (RDFG) - F29-14 (GND)

      Ignition switch ON (IG)

      Rear window defogger switch ON

      Below 1 V
      F29-38 (RDFG) - F29-14 (GND)

      Ignition switch ON (IG)

      Rear window defogger switch OFF

      11 to 14 V

    NG
    OK
  6. CHECK HARNESS AND CONNECTOR (BACK DOOR GLASS (REAR WINDOW DEFOGGER) - DEF RELAY AND BODY GROUND)


    1. Disconnect the O2 and Q1 back door glass (rear window defogger) connectors.

    2. Remove the DEF relay from the No. 2 engine room relay block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O2-1 - Relay terminal 3 Always Below 1 Ω
      Q1-1 - Body ground Always Below 1 Ω
      O2-1 - Body ground Always 10 kΩ or higher

    OK
    NG