ROOF HEADLINING REMOVAL

PROCEDURE


  1. REMOVE DECK BOARD ASSEMBLY


    1. A01UYIR

      Remove the deck board.

  2. REMOVE SPARE WHEEL COVER


    1. A01UY0I

      Remove the spare wheel cover.

  3. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)

    Click here

  4. REMOVE REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)

    Click here

  5. REMOVE FRONT DOOR SCUFF PLATE RH


    1. A01UZV1

      Disengage the 8 claws and remove the front door scuff plate.

  6. REMOVE FRONT DOOR SCUFF PLATE LH

    Tech Tips

    Use the same procedure as for the RH side.

  7. REMOVE COWL SIDE TRIM BOARD RH


    1. A01V00D

      Remove the clip.

    2. Disengage the clip and remove the cowl side trim board.

  8. REMOVE COWL SIDE TRIM BOARD LH

    Tech Tips

    Use the same procedure as for the RH side.

  9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01UZST

      Remove the front door opening trim weatherstrip.

  10. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    Tech Tips

    Use the same procedure as for the RH side.

  11. REMOVE FRONT FLOOR COVER RH (for Front Floor Cover Type A)

    Click here

  12. REMOVE FRONT FLOOR COVER LH (for Front Floor Cover Type A)

    Click here

  13. REMOVE CENTER FRONT FLOOR COVER (for Front Floor Cover Type B)

    Click here

  14. REMOVE FRONT FLOOR COVER RH (for Front Floor Cover Type B)

    Click here

  15. REMOVE FRONT FLOOR COVER LH (for Front Floor Cover Type B)

    Click here

  16. REMOVE REAR DOOR SCUFF PLATE RH


    1. A01V1R0

      Disengage the 5 claws and guide and remove the rear door scuff plate.

  17. REMOVE REAR DOOR SCUFF PLATE LH

    Tech Tips

    Use the same procedure as for the RH side.

  18. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01V085

      Remove the rear door opening trim weatherstrip.

  19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    Tech Tips

    Use the same procedure as for the RH side.

  20. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY RH


    1. A01UZGM

      Disengage the 2 claws and remove the anchor cover.

    2. A01UZ27

      Remove the bolt and separate the front seat outer belt.

  21. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the RH side.

  22. REMOVE CENTER PILLAR LOWER GARNISH RH


    1. A01V1H3

      Disengage the 2 clips and the 2 claws.

    2. Disengage the 2 guides and remove the center pillar lower garnish.

  23. REMOVE CENTER PILLAR LOWER GARNISH LH

    Tech Tips

    Use the same procedure as for the RH side.

  24. REMOVE CENTER PILLAR UPPER GARNISH RH


    1. A01V0TB

      Remove the 2 screws and disengage the clip.

    2. Pass the front seat outer belt through the slit in the center pillar upper garnish and remove the center pillar upper garnish.

  25. REMOVE CENTER PILLAR UPPER GARNISH LH

    Tech Tips

    Use the same procedure as for the RH side.

  26. REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)


    1. A01UY2AE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Disengage the front pillar garnish clip and the clip.

      Tech Tips

      The front pillar garnish clip should remain between the front pillar garnish and the pillar.

    2. A01UY3PE01
      Text in Illustration
      *1 Protective Tape

      Using needle nose pliers, turn the front pillar garnish clip 90° and disengage it from the front pillar garnish.

      Note


      • As a pillar garnish clip is reusable, do not remove it from the pillar as long as it is not damaged.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tech Tips

      Tape the needle-nosed pliers tip before use.

    3. Disengage the 2 guides and remove the front pillar garnish.

    4. for 6 speakers:


      1. Disconnect the connector.

    5. A01UZIZE08
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  27. REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

    Tech Tips

    Use the same procedure as for the RH side.

  28. REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)


    1. A01V0RP

      Disengage the 2 clips and the 2 guides and remove the front pillar garnish.

    2. for 6 speakers:


      1. Disconnect the connector.

  29. REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure as for the RH side.

  30. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for 8 Speakers)

    Click here

  31. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  32. REMOVE JACK HANDLE

  33. REMOVE REAR FLOOR FINISH PLATE


    1. A01UY1Z

      Disengage the 4 claws and 4 guides and remove the rear floor finish plate.

  34. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH


    1. A01UY3Z

      Remove the bolt.

    2. Disengage the 2 claws and separate the rear seat 3 point type outer belt.

  35. SEPARATE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the RH side.

  36. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. A01V14A

      Remove the 3 screws.

    2. Disengage the 4 claws and the guide.

    3. Disengage the 3 clips and remove the deck trim side panel.

  37. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the RH side.

  38. REMOVE ROOF SIDE INNER GARNISH RH


    1. A01V0FJ

      Disengage the 4 clips.

    2. Pass the rear seat 3 point type outer belt through the slit in the roof side inner garnish and remove the roof side inner garnish.

  39. REMOVE ROOF SIDE INNER GARNISH LH

    Tech Tips

    Use the same procedure as for the RH side.

  40. REMOVE VISOR ASSEMBLY RH


    1. A01UYFB

      Remove the visor shaft from the visor holder.

    2. Remove the 2 screws and the visor.

  41. REMOVE VISOR ASSEMBLY LH

    Tech Tips

    Use the same procedure as for the RH side.

  42. REMOVE VISOR HOLDER


    1. A01V0K0E04

      Turn the visor holder clockwise 45° and disengage the 2 claws to remove the visor holder.

      Tech Tips

      Use the same procedure for the LH side and RH side.

  43. REMOVE ASSIST GRIP ASSEMBLY

    Tech Tips

    Use the same procedure to remove all assist grips.


    1. A01UXVX

      Using a moulding remover, disengage the 4 claws and remove the 2 assist grip covers.

    2. A01V0CP

      Disengage the 2 clips and remove the assist grip.

  44. REMOVE MAP LIGHT ASSEMBLY

    Click here

  45. REMOVE VANITY LIGHT ASSEMBLY (w/ Vanity Light)

    Click here

  46. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  47. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  48. SEPARATE REAR CENTER SEAT OUTER BELT ASSEMBLY


    1. A01UZB3

      Disengage the 2 claws and open the slip joint cover.

    2. A01V10V

      Loosen the bolt and separate the rear center seat outer belt.

  49. REMOVE ROOF HEADLINING ASSEMBLY (for Glass Roof)

    A01UY85E03
    Text in Illustration
    *a Front Pillar RH Side *b Front Pillar LH Side
    *c Rear Pillar RH Side *d Windshield Glass Side

    1. for front pillar RH side:


      1. Disconnect the connector.

      2. Using a clip remover, disengage the 4 clamps.

    2. for front pillar LH side:


      1. Disconnect the connector.

      2. Using a clip remover, disengage the 4 clamps.

    3. for rear pillar RH side:


      1. Disconnect the connector.

      2. Using a clip remover, disengage the 3 clamps.

    4. for windshield glass side (w/ Rain Sensor):


      1. Disconnect the 2 connectors.

    5. Disengage the 2 claws.

    6. Using a clip remover, remove the clip.

    7. Disengage the 12 hook-and loop fasteners.

    8. A01UY40

      Remove the roof headlining from the vehicle through the back door as shown in the illustration.

      Note

      Do not damage the roof headlining assembly or body interior.

  50. REMOVE ROOF HEADLINING ASSEMBLY (except Glass Roof)

    A01UYKHE03
    Text in Illustration
    *a Front Pillar RH Side *b Front Pillar LH Side
    *c Rear Pillar RH Side *d Windshield Glass Side

    1. for front pillar RH side:


      1. Disconnect the connector.

      2. Using a clip remover, disengage the 4 clamps.

    2. for front pillar LH side:


      1. Disconnect the connector.

      2. Using a clip remover, disengage the 4 clamps.

    3. for rear pillar RH side:


      1. Disconnect the connector.

      2. Using a clip remover, disengage the 3 clamps.

    4. for windshield glass side (w/ Rain Sensor):


      1. Disconnect the 2 connectors.

    5. Disengage the 2 claws.

    6. Using a clip remover, remove the 3 clips.

    7. Disengage the 2 hooks.

    8. A01V1NZ

      Remove the roof headlining from the vehicle through the back door as shown in the illustration.

      Note

      Do not damage the roof headlining assembly or body interior.