POWER WINDOW CONTROL SYSTEM DATA LIST / ACTIVE TEST


  1. READ DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON (IG).

    3. Turn the GTS on.

    4. Enter the following menus:


      • for D-Door Motor: Body Electrical / D-Door Motor / Data List

      • for Main Body: Body Electrical / Main Body / Data List

    5. According to the display on the GTS, read the Data List.

      D-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door P/W Auto SW

      Driver side power window auto switch signal /

      ON or OFF

      ON: Driver side door power window auto switch operated

      OFF: Driver side door power window auto switch not operated

      		 -
      D Door P/W Up SW

      Driver side power window manual up switch signal /

      ON or OFF

      ON: Driver side door power window manual up switch operated

      OFF: Driver side door power window manual up switch not operated

      		 -
      D Door P/W Down SW

      Driver side power window manual down switch signal /

      ON or OFF

      ON: Driver side door power window manual down switch operated

      OFF: Driver side door power window manual down switch not operated

      		 -
      Glass Position (Close - 1/4)

      Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position /

      OK or Caution

      OK: Normal manual up operation

      Caution: Jam detected in the specified range

      		 Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
      Glass Position (1/4 - 2/4)

      Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position /

      OK or Caution

      OK: Normal manual up operation

      Caution: Jam detected in the specified range

      		 Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
      Glass Position (2/4 - 3/4)

      Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position /

      OK or Caution

      OK: Normal manual up operation

      Caution: Jam detected in the specified range

      		 Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
      Glass Position (3/4 - Open)

      Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position /

      OK or Caution

      OK: Normal manual up operation

      Caution: Jam detected in the specified range

      		 Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam.
      Number of Trouble Codes

      Number of trouble codes /

      Min.: 0

      Max.: 255

      		 Number of DTCs will be displayed -
      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      FR Door Courtesy SW

      Front door courtesy light switch RH signal /

      ON or OFF

      ON: Front door RH closed

      OFF: Front door RH opened

      		 -
      FL Door Courtesy SW

      Front door courtesy light switch LH signal /

      ON or OFF

      ON: Front door LH closed

      OFF: Front door LH opened

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON (IG).

    3. Turn the GTS on.

    4. Enter the following menus:

      for D-Door Motor: Body Electrical / D-Door Motor / Active Test

      for Main Body: Body Electrical / Main Body / Active Test

    5. According to the display on the GTS, perform the Active Test.

      CAUTION:

      Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

      D-Door Motor
      Tester Display Test Part Control Range Diagnostic Note
      Power Window Power window OFF / DOWN / UP -
      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      IG OFF P/W Control Permission Output Power window OFF / ON Perform this Active Test with the ignition switch off