AIR CONDITIONING SYSTEM, Diagnostic DTC:B1413/13

DTC Code DTC Name
B1413/13 Evaporator Temperature Sensor Circuit

DESCRIPTION

The No. 1 cooler thermistor (evaporator temperature sensor) is installed on the evaporator in the air conditioning unit to detect the temperature of the cooled air that has passed through the evaporator and control the air conditioning. It sends appropriate signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor (evaporator temperature sensor) changes in accordance with the temperature of the cooled air that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor (evaporator temperature sensor) and reads voltage changes as the resistance of the No. 1 cooler thermistor (evaporator temperature sensor) changes. This sensor is used for frost prevention.

DTC No. DTC Detection Condition Trouble Area
B1413/13 An open or short in the No. 1 cooler thermistor (evaporator temperature sensor) circuit.

  • No. 1 cooler thermistor (evaporator temperature sensor)

  • Air conditioning harness assembly

  • Air conditioning amplifier assembly

WIRING DIAGRAM

A01V1EJE02

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Data List.

    5. According to the display on the GTS, read the Data List.

      Air Conditioner
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Evaporator Fin Thermistor

      Evaporator temperature sensor /

      Min.: -29.7°C (-21.46°F)

      Max.: 59.55°C (139.19°F)

      		 Actual evaporator temperature displayed -
      OK
      The display is as specified in the normal condition column.
      Result
      Result Proceed to
      OK (When troubleshooting according to the DTC) A
      OK (When troubleshooting according to Problem Symptoms Table) B
      NG C

    B

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    C

    INSPECT NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR) Click here

    A

  2. CHECK FOR DTC


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      OK
      DTC B1413/13 is not output

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

  3. INSPECT NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)


    1. Inspect the No. 1 cooler thermistor (evaporator temperature sensor) Click here.


    NG

    REPLACE NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR) Click here

    OK

  4. INSPECT AIR CONDITIONING HARNESS ASSEMBLY (NO. 1 COOLER THERMISTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. Remove the air conditioning harness assembly.

    2. A01V23EE02
      Text in Illustration
      *1 Air Conditioning Harness Assembly

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-2 - z1-6 (TEA) Always Below 1 Ω
      A-1 - z1-5 (SGA) Always Below 1 Ω
      A-2 - Body ground Always 10 kΩ or higher
      A-1 - Body ground Always 10 kΩ or higher

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    NG

    REPLACE AIR CONDITIONING HARNESS ASSEMBLY Click here