FRONT SEAT OUTER BELT ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing Click here.

Tech Tips

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.

PROCEDURE


  1. INSTALL FRONT SEAT OUTER BELT ASSEMBLY


    1. A01V1MVE03
      Text in Illustration
      *a Unlock
      *b Lock

      Check the angle of inclination required to lock the retractor.


      1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15 ° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45 ° or more.

        Note

        Do not disassemble the retractor.

        If the operation is not as specified, replace the front seat outer belt assembly.

    2. A01UZ2CE01

      Engage the 2 hooks and temporarily install the front seat outer belt assembly with the 2 bolts.

    3. Tighten bolt A and then bolt B.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }
      for bolt A
      41 N*m  { 420 kgf*cm, 30 ft.*lbf }
      for bolt B
    4. A01V1KPE01
      Text in Illustration
      *1 Locking Button

      Connect the pretensioner connector.

    5. Lock the locking button.

      Note

      Securely lock the locking button.

    6. Install the shoulder anchor part of the front seat outer belt assembly with the bolt.

      Torque:
      41 N*m  { 420 kgf*cm, 30 ft.*lbf }

    7. Install the floor anchor part of the front seat outer belt assembly with the bolt.

      Torque:
      41 N*m  { 420 kgf*cm, 30 ft.*lbf }

    8. Check that the ELR locks.

      Note


      • The check should be performed with the front seat outer belt installed.

      • Do not allow the anchor part of the front seat outer belt and the protruding parts of the floor panel to overlap.


      1. With the belt installed, check that the belt locks when it is pulled out quickly.

        If the operation is not as specified, replace the front seat outer belt.

    9. Remove the bolt and disconnect the floor anchor part of the front seat outer belt assembly.

  2. INSTALL CENTER PILLAR UPPER GARNISH

    Click here

  3. INSTALL CENTER PILLAR LOWER GARNISH

    Click here

  4. CONNECT FRONT SEAT OUTER BELT ASSEMBLY


    1. Install the floor anchor part of the front seat outer belt assembly with the bolt.

      Torque:
      41 N*m  { 420 kgf*cm, 30 ft.*lbf }

    2. Engage the 3 claws and install the lap belt outer anchor cover.

  5. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP

    Click here

  6. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

    Click here

  7. INSTALL REAR DOOR SCUFF PLATE

    Click here

  8. INSTALL FRONT DOOR SCUFF PLATE

    Click here

  9. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  10. INSTALL FRONT FLOOR COVER LH (for LH Side)

    Install the front floor cover LH (for Front Floor Cover Type A). Click here

    Install the front floor cover LH (for Front Floor Cover Type B). Click here

  11. INSTALL FRONT FLOOR COVER RH (for Front Floor Cover Type A)

    Click here

  12. INSTALL FRONT FLOOR COVER RH (for Front Floor Cover Type B)

    Click here

  13. INSTALL CENTER FRONT FLOOR COVER (for Front Floor Cover Type B)

    Click here

  14. INSPECT SRS WARNING LIGHT

    Click here